|
SIST EN 1870-1:2007/kprA1:2008
01-oktober-2008
9DUQRVWOHVQRREGHORYDOQLKVWURMHY.URåQHåDJHGHO 'HORYQHPL]H V
SRGDMDOQRPL]RDOLEUH]QMH åDJH]DUH]DQMHQDPHURLQåDJHQDJUDGELãþX
Safety of woodworking machines - Circular sawing machines - Part 1: Circular saw
benches (with and without sliding table), dimension saws and building site saws
Sicherheit von Holzbearbeitungsmaschinen - Kreissägemaschinen - Teil 1:
Tischkreissägemaschinen (mit und ohne Schiebetisch), Formatkreissägemaschinen und
Baustellenkreissägemaschinen
Sécurité des machines pour le travail du bois - Machines à scier circulaires - Partie 1:
Scies circulaires à table de menuisier (avec ou sans table mobile), scies au format et
scies de chantier
Ta slovenski standard je istoveten z: EN 1870-1:2007/prA1
ICS:
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 1870-1:2007/kprA1:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1870-1:2007/kprA1:2008
---------------------- Page: 2 ----------------------
SIST EN 1870-1:2007/kprA1:2008
EUROPEAN STANDARD
FINAL DRAFT
EN 1870-1:2007
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
June 2008
ICS 79.120.10
English Version
Safety of woodworking machines - Circular sawing machines -
Part 1: Circular saw benches (with and without sliding table),
dimension saws and building site saws
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
scier circulaires - Partie 1: Scies circulaires à table de Kreissägemaschinen - Teil 1: Tischkreissägemaschinen
menuisier (avec ou sans table mobile), scies au format et (mit und ohne Schiebetisch), Formatkreissägemaschinen
scies de chantier und Baustellenkreissägemaschinen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A1, if approved, will modify the European Standard EN 1870-1:2007. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36 B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1870-1:2007/prA1:2008: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 1870-1:2007/kprA1:2008
EN 1870-1:2007/prA1:2008 (E)
Contents Page
Foreword.3
1 Modification to the Foreword .4
2 Modification to 5.4.5, Ergonomics and handling.4
3 Modification to 6.2.1, Marking of the machine.4
4 Modification to 6.3, Instruction handbook .4
5 Modification to Annex ZA .4
6 Addition of Annex ZB .5
2
---------------------- Page: 4 ----------------------
SIST EN 1870-1:2007/kprA1:2008
EN 1870-1:2007/prA1:2008 (E)
Foreword
This document (EN 1870-1:2007/prA1:2008) has been prepared by Technical Committee CEN/TC 142
“Woodworking machines - Safety”, the secretariat of which is held by UNI.
This document is currently submitt
...