EN 71-1:2005/prA6

Safety of toys - Part 1: Mechanical and physical properties

EN 71-1:2005/prA6

Name:EN 71-1:2005/prA6   Standard name:Safety of toys - Part 1: Mechanical and physical properties
Standard number:EN 71-1:2005/prA6   language:English language
Release Date:   technical committee:CEN/TC 52 - Safety of toys
Drafting committee:CEN/TC 52/WG 3 - Safety of toys - Mechanical, physical and general properties   ICS number:97.200.50 - Toys
SLOVENSKI STANDARD
SIST EN 71-1:2006/oprA6:2008
01-januar-2008
9DUQRVWLJUDþGHO0HKDQVNHLQIL]LNDOQHODVWQRVWL'RSROQLOR$
Safety of toys - Part 1: Mechanical and physical properties
Sicherheit von Spielzeug - Teil 1: Mechanische und physikalische Eigenschaften
Sécurité des jouets - Partie 1: Propriétés mécaniques et physiques
Ta slovenski standard je istoveten z: EN 71-1:2005/prA6
ICS:
97.200.50 ,JUDþH Toys
SIST EN 71-1:2006/oprA6:2008 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
FINAL DRAFT
EN 71-1:2005
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA6
October 2007
ICS 97.200.50

English Version
Safety of toys - Part 1: Mechanical and physical properties
Sécurité des jouets - Partie 1: Propriétés mécaniques et Sicherheit von Spielzeug - Teil 1: Mechanische und
physiques physikalische Eigenschaften
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 52.
This draft amendment A6, if approved, will modify the European Standard EN 71-1:2005. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
: This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
Warning
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2007 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 71-1:2005/prA6:2007: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN 71-1:2005/prA6:2007 (E)
Contents Page
Foreword.3
1 Modification to 4.8 .4
2 Modification to 4.21 .4
3 Modification to 5.12 .4
4 Modification to 8.6 .4
5 Modification to 8.13 .5
6 Modification to 8.22 .6
7 Modification to 8.28.2.3.4 .6
8 Modification to A.9.7
9 Modification to A.50.7

2

---------------------- Page: 3 ----------------------

EN 71-1:2005/prA6:2007 (E)
Foreword
This document (EN 71-1:2005/prA6:2007) has been prepared by Technical Committee CEN/TC 52 “Safety of
toys”, the secretariat of which is held by DS.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EC Directive(s).
For relationship with EC Directive(s), see informative Annex ZA, which is an integral part of this document.
3

---------------------- Page: 4 ----------------------

EN 71-1:2005/prA6:2007 (E)
1 Modification to 4.8
Replace 4.8 c) with the following:
"c) Wires and other
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27