|
SIST EN 16153:2013/kFprA1:2014
01-september-2014
3URVRMQHSORãþDWHYHþVORMQHSROLNDUERQDWQH3&SORãþH]DQRWUDQMHLQ]XQDQMH
VWUHKHVWHQHLQVWURSH=DKWHYHLQSUHVNXVQHPHWRGH
Light transmitting flat multiwall polycarbonate (PC) sheets for internal and external use in
roofs, walls and ceilings - Requirements and test methods
Lichtdurchlässige, flache Stegmehrfachplatten aus Polycarbonat (PC) für Innen- und
Außenanwendungen an Dächern, Wänden und Decken - Anforderungen und
Prüfverfahren
Plaques d’éclairement multiparois et planes en polycarbonate (PC) pour usage intérieur
ou extérieur dans les toitures, bardages et plafonds - Exigences et méthodes d’essai
Ta slovenski standard je istoveten z: EN 16153:2013/FprA1
ICS:
83.140.10 Filmi in folije Films and sheets
91.060.01 Stavbni elementi na splošno Elements of buildings in
general
SIST EN 16153:2013/kFprA1:2014 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 16153:2013/kFprA1:2014
---------------------- Page: 2 ----------------------
SIST EN 16153:2013/kFprA1:2014
EUROPEAN STANDARD
FINAL DRAFT
EN 16153:2013
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
May 2014
ICS 83.140.10; 91.060.01
English Version
Light transmitting flat multiwall polycarbonate (PC) sheets for
internal and external use in roofs, walls and ceilings -
Requirements and test methods
Plaques d'éclairement multiparois et planes en Lichtdurchlässige, flache Stegmehrfachplatten aus
polycarbonate (PC) pour usage intérieur ou extérieur dans Polycarbonat (PC) für Innen- und Außenanwendungen an
les toitures, bardages et plafonds - Exigences et méthodes Dächern, Wänden und Decken - Anforderungen und
d'essai Prüfverfahren
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 128.
This draft amendment A1, if approved, will modify the European Standard EN 16153:2013. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 16153:2013/FprA1:2014 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 16153:2013/kFprA1:2014
EN 16153:2013/FprA1:2014 (E)
Contents
Page
Foreword .3
Introduction .4
1 Modification to Table 1 .5
2 Modification to 4.3 .5
3 Modification to5.2.1.2 .5
4 Modification to 5.6.4.2.1 .5
5 Modification to 5.6.4.2.2 .6
6 Modification to 5.6.6 .
...