EN 1591-1:2001/prA1

Flanges and their joints - Design rules for gasketed circular flange connections - Part 1: Calculation method

EN 1591-1:2001/prA1

Name:EN 1591-1:2001/prA1   Standard name:Flanges and their joints - Design rules for gasketed circular flange connections - Part 1: Calculation method
Standard number:EN 1591-1:2001/prA1   language:English language
Release Date:   technical committee:CEN/TC 74 - Flanges and their joints
Drafting committee:CEN/TC 74/WG 10 - Calculation methods   ICS number:23.040.60 - Flanges, couplings and joints
SLOVENSKI SIST EN 1591-1:2002/opr
A1:2005

PREDSTANDARD
november 2005
Prirobnice in prirobnični spoji – Pravila za načrtovanje okroglih prirobničnih
spojev s tesnili – 1. del: Način izračuna – Dopolnilo 1
Flanges and their joints - Design rules for gasketed circular flange con-nections -
Part 1: Calculation method - Amendment 1
ICS 23.040.60 Referenčna številka
SIST EN 1591-1:2002/opr A1:2005(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------

EUROPEAN STANDARD
DRAFT
EN 1591-1:2001
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
September 2005
ICS

English Version
Flanges and their joints - Design rules for gasketed circular
flange con-nections - Part 1: Calculation method - Amendment 1
Flansche und ihre Verbindungen - Regeln für die
Auslegung von Flanschverbindungen mit runden Flanschen
und Dichtung - Teil 1: Berechnungsmethode - Änderung 1
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 74.
This draft amendment A1, if approved, will modify the European Standard EN 1591-1:2001. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same status
as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2005 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1591-1:2001/A1:2005:2005: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------

EN 1591-1:2001/prA1:2005 (E)
Contents Seite
Foreword.3
1.3.4 Mechanical model.4
3.2 Subscripts and special marks .5
3.2.1 Subscripts.5
3.2.2 Special marks.6
3.3 Symbols.6
4.3 Gasket parameters.10
4.3.1 Theoretical dimensions.10
4.3.2 Effective dimensions.10
4.3.3 Axial flexibility modulus of gasket.11
5.2 Compliance of the joint .13
5.3 Minimum forces necessary for the gasket.13
5.3.1 Assembly condition (I = 0) .13
5.3.2 Subsequent conditions (I = 1, 2, .) .14
5.4 Intern
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27