EN ISO 23062:2022

Foundry machinery - Safety requirements for molding and coremaking machinery and associated equipment (ISO 23062:2022)

EN ISO 23062:2022

Name:EN ISO 23062:2022   Standard name:Foundry machinery - Safety requirements for molding and coremaking machinery and associated equipment (ISO 23062:2022)
Standard number:EN ISO 23062:2022   language:English language
Release Date:20-Dec-2022   technical committee:CEN/TC 202 - Foundry machinery
Drafting committee:CEN/TC 202/WG 2 - Moulding and core making   ICS number:13.110 - Safety of machinery

SLOVENSKI STANDARD
01-marec-2023
Nadomešča:
SIST EN 710:2000+A1:2010
SIST EN 710:2000+A1:2010/AC:2013
Livarski stroji - Varnostne zahteve za stroje za oblikovanje in izdelavo jeder ter
pripadajočo opremo (ISO 23062:2022)
Foundry machinery - Safety requirements for molding and coremaking machinery and
associated equipment (ISO 23062:2022)
Sicherheit von Maschinen - Sicherheitsanforderungen an Gießereimaschinen und -
anlagen der Form- und Kernherstellung und dazugehörige Einrichtungen (ISO
23062:2022)
Machines de fonderie - Prescriptions de sécurité pour les machines et équipements
associés de moulage et de noyautage (ISO 23062:2022)
Ta slovenski standard je istoveten z: EN ISO 23062:2022
ICS:
25.120.30 Livarska oprema Moulding equipment
77.180 Oprema za metalurško Equipment for the
industrijo metallurgical industry
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN ISO 23062
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2022
EUROPÄISCHE NORM
ICS 13.110; 25.120.30; 77.180 Supersedes EN 710:1997+A1:2010
English Version
Foundry machinery - Safety requirements for molding and
coremaking machinery and associated equipment (ISO
23062:2022)
Machines de fonderie - Prescriptions de sécurité pour Sicherheit von Maschinen - Sicherheitsanforderungen
les machines et équipements associés de moulage et de an Gießereimaschinen und -anlagen der Form- und
noyautage (ISO 23062:2022) Kernherstellung und dazugehörige Einrichtungen (ISO
23062:2022)
This European Standard was approved by CEN on 27 June 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 23062:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 3
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of EU Directive 2006/42/EC aimed to be covered . 4

European foreword
This document (EN ISO 23062:2022) has been prepared by Technical Committee ISO/TC 306 "Foundry
machinery" in collaboration with Technical Committee CEN/TC 202 “Foundry machinery” the
secretariat of which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by June 2023, and conflicting national standards shall be
withdrawn at the latest by June 2023.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN 710:1997+A1:2010.
This document has been prepared under a Standardization Request given to CEN by the European
Commission and the European Free Trade Association, and supports essential requirements of EU
Directive(s) / Regulation(s).
For the relationship with EU Directive(s) / Regulation(s), see informative Annex ZA, which is an integral
part of this document.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and the
United Kingdom.
Endorsement notice
The text of ISO 23062:2022 has been approved by CEN as EN ISO 23062:2022 without any modification.

Annex ZA
(informative)
Relationship between this European Standard and the essential
requirements of EU Directive 2006/42/EC aimed to be covered
This European Standard has been prepared under a Commission’s standardization request “M/396
Mandate to CEN and CENELEC for Standardisation in the field of machinery" to provide one voluntary
means of conforming to essential requirements of Directive 2006/42/EC of the European Parliament
and of the Council of 17 May 2006 on machinery, and amending Directive 95/16/EC (recast).
Once this standard is cited in the Official Journal of the European Union under that Directive,
compliance with the normative clauses of this standard given in Table ZA.1 confers, within the limits of
the scope of this standard, a presumption of conformity with the corresponding essential requirements
of that Directive, and associated EFTA regulations.
Table ZA.1 — Correspondence between this European Standard and Directive 2006/42/EC
The relevant Essential Clause(s)/sub-clause(s) of this EN Remarks/Notes
Requirements of Directive
2006/42/EC
1.1.3. Materials and products 5.1.7; 5.1.16
1.1.5. Design of machinery to
facilitate its handling 5.1.11; 5.1.19
1.1.6. Ergonomics 5.1.11
1.2.1. Safety and reliability of
control systems 5.1.5
5.1.1; 5.1.2; 5.1.3; 5.1.4; 5.1.5; 5.1.6;
1.3. Protection against 5.1.7;5.1.11;5.1.13; 5.1.14; 5.1.15; 5.1.16; 5.1.18;
mechanical hazards 5.1.19
1.5.1. Electricity supply 5.1.7; 5.1.14
1.5.13. Emissions of hazardous
materials and substances 5.1.7; 5.1.16
1.5.14. Risk of being trapped in a
machine 5.1.2; 5.1.6
1.5.5. Extreme temperatures 5.1.1; 5.1.2; 5.1.3; 5.1.6; 5.1.14; 5.1.17
1.5.6. Fire 5.1.6; 5.1.7; 5.1.17
1.5.7. Explosion  Not covered
1.5.8. Noise  Not covered
1.5.9. Vibrations Not covered
1.6.1. Machinery maintenance 5.1.4, 5.1.5, 5.1.7; 5.1.14
1.6.5. Cleaning of internal parts 5.1.16; 5.1.17
7.4.2
17.1. Information and warnings
on the machinery
1.7.1.1. Information and
information devices 7.4.2
1.7.1.2. Warning devices 7.2, 7.4.2
1.7.2. Warning of residual risks 7.2, 7.4.2
1.7.3. Marking of machinery 7.4.2
1.7.4. Instructions 7.4.2
1.7.4.1. General principles for the
drafting of instructions 7.4.2
1.7.4.2. Contents of the
instructions 7.4.2
1.7.4.3 Sales literature  Not covered
WARNING 1 — Presumption of conformity stays valid only as long as a reference to this European
Standard is maintained in the list published in the Official Journal of the European Union. Users of this
standard should consult frequently the latest list published in the Official Journal of the European
Union.
WARNING 2 — Other Union legislation may be applicable to the product(s) falling within the scope of
this standard.
INTERNATIONAL ISO
STANDARD 23062
First edition
2022-07
Foundry machinery — Safety
requirements for molding and
coremaking machinery and associated
equipment
Machines de fonderie — Prescriptions de sécurité pour les machines
et équipements associés de moulage et de noyautage
Reference number
ISO 23062:2022(E)
ISO 23062:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: [email protected]
Website: www.iso.org
Published in Switzerland
ii
ISO 23062:2022(E)
Contents Page
Foreword .v
Introduction . vi
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 2
4 Significant hazards and risk assessment . 6
4.1 General . 6
4.2 Interfaces to the linked/integrated equipment . 7
5 Safety requirements and/or protective/risk reduction measures .7
5.1 General . 7
5.1.1 Fixed guards . 7
5.1.2 Movable guards . 7
5.1.3 Electro-sensitive protective devices (ESPD) . 8
5.1.4 Several persons at the same time being present at hazardous zones . 8
5.1.5 Control systems . 8
5.1.6 Electrical equipment . 9
5.1.7 Safety-related control systems . 9
5.1.8 Safety-related software and parameters . 9
5.1.9 Remote access to the control systems . 10
5.1.10 Two-hand control devices . 10
5.1.11 Ergonomics . 10
5.1.12 Noise . 11
5.1.13 Vibrations . 12
5.1.14 Surface temperatures and heat radiation .12
5.1.15 Safety signs and warning devices .12
5.1.16 Exhaust systems . 13
5.1.17 Fire and explosion protection.
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27