EN 869:2006/prA1

Foundry machinery - Safety requirements for pressure metal diecasting units

EN 869:2006/prA1

Name:EN 869:2006/prA1   Standard name:Foundry machinery - Safety requirements for pressure metal diecasting units
Standard number:EN 869:2006/prA1   language:English language
Release Date:   technical committee:CEN/TC 202 - Foundry machinery
Drafting committee:CEN/TC 202/WG 1 - Die casting   ICS number:25.120.30 - Moulding equipment
SLOVENSKI STANDARD
SIST EN 869:2007/kprA1:2008
01-november-2008
9DUQRVWVWURMHY9DUQRVWQH]DKWHYH]DHQRWH]DWODþQRXOLYDQMHNRYLQ
Foundry machinery - Safety requirements for pressure metal diecasting units
Gießereimaschinen - Sicherheitsanforderungen an Metall-Druckgießanlagen
Machines de fonderie - Prescriptions de sécurité pour les unités à mouler les métaux
sous haute pression
Ta slovenski standard je istoveten z: EN 869:2006/prA1
ICS:
25.120.30 Livarska oprema Moulding equipment
SIST EN 869:2007/kprA1:2008 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN 869:2007/kprA1:2008

---------------------- Page: 2 ----------------------

SIST EN 869:2007/kprA1:2008
EUROPEAN STANDARD
FINAL DRAFT
EN 869:2006
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
August 2008
ICS 25.120.30

English Version
Foundry machinery - Safety requirements for pressure metal
diecasting units
Machines de fonderie - Prescriptions de sécurité pour les Gießereimaschinen - Sicherheitsanforderungen an Metall-
unités à mouler les métaux sous haute pression Druckgießanlagen
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 202.
This draft amendment A1, if approved, will modify the European Standard EN 869:2006. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2008 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 869:2006/prA1:2008: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN 869:2007/kprA1:2008
EN 869:2006/prA1:2008 (E)
Contents Page
Foreword.3
1 Modification to "Foreword" .4
2 Modification to "Introduction".4
3 Modification to Clause "2 Normative references".4
4 Modification to the whole document due to new/updated standards.5
5 Modification to "4.4 Thermal hazards" .5
6 Modification to "5.2 Mechanical" .5
6.1 Modification to "5.2.1 General" .5
6.2 Modification to 5.2.2.1 .5
6.3 Modification to 5.2.2.2 .5
6.4 Modification to "5.2.3 Guards for the die closing mechanism area".6
6.5 Modification to 5.2.4.4 .6
7 Modification to "5.3 Electric equipment and control systems" .6
7.1 Modification to 5.3.2 .6
7.2 Modification to 5.3.3 .
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27