|
SIST EN 12666-1:2006/oprA1:2010
01-maj-2010
Cevni sistemi iz polimernih materialov za odpadno vodo in kanalizacijo, ki delujejo
po težnostnem principu in so položeni v zemljo - Polietilen (PE) – 1. del:
Specifikacije za cevi, fitinge in sistem
Plastics piping systems for non-pressure underground drainage and sewerage -
Polyethylene (PE) - Part 1: Specifications for pipes, fittings and the system
Kunststoff-Rohrleitungssysteme für erdverlegte drucklose Abwasserkanäle und -
leitungen - Polyethylen (PE) - Teil 1: Anforderungen an Rohre, Formstücke und das
Rohrleitungssystem
Systèmes de canalisations en plastique pour les branchements et les collecteurs
d'assainissement sans pression enterrés - Polyéthylène (PE) - Partie 1: Spécifications
pour les tubes, les raccords et le système
Ta slovenski standard je istoveten z: EN 12666-1:2005/prA1
ICS:
23.040.01 Deli cevovodov in cevovodi Pipeline components and
na splošno pipelines in general
91.140.80 Drenažni sistemi Drainage systems
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
SIST EN 12666-1:2006/oprA1:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 12666-1:2006/oprA1:2010
---------------------- Page: 2 ----------------------
SIST EN 12666-1:2006/oprA1:2010
EUROPEAN STANDARD
DRAFT
EN 12666-1:2005
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
March 2010
ICS 23.040.01; 93.030
English Version
Plastics piping systems for non-pressure underground drainage
and sewerage - Polyethylene (PE) - Part 1: Specifications for
pipes, fittings and the system
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für erdverlegte drucklose
branchements et les collecteurs d'assainissement sans Abwasserkanäle und -leitungen - Polyethylen (PE) - Teil 1:
pression enterrés - Polyéthylène (PE) - Partie 1: Anforderungen an Rohre, Formstücke und das
Spécifications pour les tubes, les raccords et le système Rohrleitungssystem
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 155.
This draft amendment A1, if approved, will modify the European Standard EN 12666-1:2005. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 12666-1:2005/prA1:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 12666-1:2006/oprA1:2010
EN 12666-1:2005/prA1:2010 (E)
Contents Page
1 Changes to foreword .4
2 Change to Clause 1 Scope .4
3 Changes to Clause 2 Normative references .4
4 Change to 3.3 Abbreviations .4
5 Change to 4.2 Reprocessable and recyclable material .4
6 Changes to 4.3 Melt mass-flow rate .5
7 Changes to 6.2.1 Outside diameter .
...