EN 13110:2022

LPG equipment and accessories - Transportable refillable welded aluminium cylinders for liquefied petroleum gas (LPG) - Design and construction

EN 13110:2022

Name:EN 13110:2022   Standard name:LPG equipment and accessories - Transportable refillable welded aluminium cylinders for liquefied petroleum gas (LPG) - Design and construction
Standard number:EN 13110:2022   language:English language
Release Date:20-Dec-2022   technical committee:CEN/TC 286 - Liquefied petroleum gas equipment and accessories
Drafting committee:CEN/TC 286/WG 1 - Design and manufacture of LPG pressure vessels   ICS number:23.020.35 - Gas cylinders

SLOVENSKI STANDARD
01-april-2023
Nadomešča:
SIST EN 13110:2012+A1:2017
Oprema in pribor za utekočinjeni naftni plin (UNP) - Premične ponovno polnljive
varjene jeklenke iz aluminija za UNP - Konstruiranje in izdelava
LPG equipment and accessories - Transportable refillable welded aluminium cylinders
for liquefied petroleum gas (LPG) - Design and construction
Flüssiggas-Geräte und Ausrüstungsteile - Ortsbewegliche wiederbefüllbare geschweißte
Flaschen aus Aluminium für Flüssiggas (LPG) - Auslegung und Bau
Equipements pour gaz de pétrole liquéfiés et leurs accessoires - Bouteilles soudées
transportables et rechargeables en aluminium pour gaz de pétrole liquéfié (GPL) -
Conception et construction
Ta slovenski standard je istoveten z: EN 13110:2022
ICS:
23.020.35 Plinske jeklenke Gas cylinders
77.150.10 Aluminijski izdelki Aluminium products
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 13110
EUROPEAN STANDARD
NORME EUROPÉENNE
December 2022
EUROPÄISCHE NORM
ICS 23.020.35 Supersedes EN 13110:2012+A1:2017
English Version
LPG equipment and accessories - Transportable refillable
welded aluminium cylinders for liquefied petroleum gas
(LPG) - Design and construction
Équipements pour gaz de pétrole liquéfiés et leurs Flüssiggas-Geräte und Ausrüstungsteile -
accessoires - Bouteilles soudées transportables et Ortsbewegliche, wiederbefüllbare geschweißte
rechargeables en aluminium pour gaz de pétrole Flaschen aus Aluminium für Flüssiggas (LPG) -
liquéfié (GPL) - Conception et construction Auslegung und Bau
This European Standard was approved by CEN on 28 November 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Türkiye and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 13110:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 5
Introduction . 6
1 Scope . 7
2 Normative references . 7
3 Terms, definitions and symbols . 8
3.1 Terms and definitions . 8
3.2 Symbols . 9
4 Materials . 10
5 Design . 11
5.1 General requirements . 11
5.2 Calculation of cylindrical wall thickness . 11
5.3 Design of ends concave to pressure. 12
5.4 Other shapes of ends . 12
5.5 Minimum wall thickness . 13
5.6 Design of openings . 13
5.7 Neck design. 13
5.8 Stability . 17
5.9 Valve protection . 17
6 Construction and workmanship . 17
6.1 Environment . 17
6.2 Welding qualification . 17
6.3 Plates and pressed parts . 18
6.4 Welded joints . 18
6.5 Tolerances . 18
6.5.1 Out of roundness . 18
6.5.2 Wall thickness . 18
6.5.3 Straightness . 18
6.5.4 Verticality. 18
6.6 Non-pressure bearing attachments . 18
6.7 Heat treatment . 19
6.8 Closure of openings . 19
7 Testing and examination . 20
7.1 General . 20
7.2 Types of test and evaluation of test results . 20
7.3 Test specimens and related tests and examinations . 21
7.3.1 Two piece cylinders . 21
7.3.2 Three piece cylinders . 21
7.3.3 Valve boss welds . 21
7.4 Tensile test . 23
7.4.1 General . 23
7.4.2 Parent material . 23
7.4.3 Welds . 23
7.5 Bend test . 23
7.5.1 Bend test on parent material . 23
7.5.2 Bend test across the welds . 24
7.5.3 Nick-break test across the welds . 24
7.6 Macroscopic examination of welds . 26
7.6.1 Procedure . 26
7.6.2 Requirements . 26
7.7 Burst test under hydraulic pressure . 27
7.7.1 Procedure . 27
7.7.2 Requirements . 28
7.8 Fatigue test . 28
7.8.1 Procedure . 28
7.8.2 Requirements . 29
7.9 Drop test . 29
7.9.1 Procedure . 29
7.9.2 Requirements . 29
7.10 Visual examination . 30
7.10.1 Procedure . 30
7.10.2 Requirements . 30
7.11 Radiographic examination . 30
7.11.1 Procedure . 30
7.11.2 Assessment. 30
7.11.3 Requirements . 30
7.12 Pressure test . 30
7.12.1 Procedure . 30
7.12.2 Requirements . 31
8 Technical requirements for type approval . 32
8.1 New cylinder design . 3
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27