|
SLOVENSKI STANDARD
01-december-2022
Nadomešča:
SIST EN ISO 15537:2005
Načela za izbiro in uporabo preskusnih oseb za preskušanje antropometričnih
vidikov industrijskih proizvodov in načrtov (ISO 15537:2022)
Principles for selecting and using test persons for testing anthropometric aspects of
industrial products and designs (ISO 15537:2022)
Grundsätze für die Auswahl und den Einsatz von Prüfpersonen zur Prüfung
anthropometrischer Aspekte von Industrieerzeugnissen und deren Gestaltung (ISO
15537:2022)
Principes de choix et d'utilisation de sujets d'essai pour l'essai des aspects
anthropométriques des produits industriels et leur conception (ISO 15537:2022)
Ta slovenski standard je istoveten z: EN ISO 15537:2022
ICS:
13.110 Varnost strojev Safety of machinery
13.180 Ergonomija Ergonomics
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 15537
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2022
EUROPÄISCHE NORM
ICS 13.110; 13.180 Supersedes EN ISO 15537:2004
English Version
Principles for selecting and using test persons for testing
anthropometric aspects of industrial products and designs
(ISO 15537:2022)
Principes de choix et d'utilisation de sujets d'essai pour Grundsätze für die Auswahl und den Einsatz von
l'essai des aspects anthropométriques des produits Prüfpersonen zur Prüfung anthropometrischer
industriels et leur conception (ISO 15537:2022) Aspekte von Industrieerzeugnissen und deren
Gestaltung (ISO 15537:2022)
This European Standard was approved by CEN on 9 May 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15537:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 15537:2022) has been prepared by Technical Committee ISO/TC 159
"Ergonomics" in collaboration with Technical Committee CEN/TC 122 “Ergonomics” the secretariat of
which is held by DIN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2022, and conflicting national standards
shall be withdrawn at the latest by December 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
This document supersedes EN ISO 15537:2004.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 15537:2022 has been approved by CEN as EN ISO 15537:2022 without any modification.
INTERNATIONAL ISO
STANDARD 15537
Second edition
2022-05
Principles for selecting and using test
persons for testing anthropometric
aspects of industrial products and
designs
Principes de choix et d'utilisation de sujets d'essai pour l'essai des
aspects anthropométriques des produits industriels et leur conception
Reference number
ISO 15537:2022(E)
ISO 15537:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: [email protected]
Website: www.iso.org
Published in Switzerland
ii
ISO 15537:2022(E)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Types of tests. 2
4.1 General . 2
4.2 Screening test . 3
4.3 Detailed test . 3
5 Test with test persons or manikins . 3
5.1 General requirements and recommendations . 3
5.2 Procedure for testing . 3
5.3 Selection of test persons within the intended user population for screening test . 4
5.4 Selection of test persons within the intended user population for detailed test . 4
5.5 Experienced or inexperienced persons . 5
5.6 Criteria for acceptance of a product with regard to anthropometric aspects . 5
5.7 Documentation of the test procedure and the results . 5
Annex A (informative) Example of a test procedure for testing of anthropometric aspects
of an elevator . 6
Bibliography . 9
iii
ISO 15537:2022(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO documents should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights. Details of
any patent rights identified during the development of the document will be in the Introduction and/or
on the ISO list of patent declarations received (see www.iso.org/patents).
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 159, Ergonomics, Subcommittee SC 3,
Anthropometry and biomechanics, in collaboration with the European Committee for Standardization
(CEN) Technical Committee CEN/TC 122, Ergonomics, in accordance with the Agreement on technical
cooperation between ISO and CEN (Vienna Agreement).
This second edition cancels and replaces the first edition (ISO 15537:2004), which has been technically
revised.
The main changes are as follows:
— the context has been broadened to include testing by computer-aided design (CAD);
— European values in tables have been replaced by global values.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
ISO 15537:2022(E)
Introduction
An investigation into how far ergonomic requirements are taken into consideration with regard to
industrial products and designs is often performed using test equipment that permits only one or a
few parameters (e.g. body height) to be registered. With regard to the concurrent multifunctional
testing and/or determination of product characteristics for which no technical testing procedures have
been established, one or more people are often designated as test persons and are observed and/or
questioned during or after product testing.
The reliability of any findings established in this way is very much dependent on the extent to which
the test persons represent the intended user group in different aspects. How well a product or design is
adjusted to the anthropometrics of the intended user population is dealt with in this document.
According to ISO 14738, workstations at machinery has to be designed with proper regard to the body
dimensions of the intended user population. One means to verify that a product or a design fulfils this
requirement is to set up a panel of test persons and let them test the product in different ways.
An example of the use of this document is given in Annex A.
v
INTERNATIONAL STANDARD ISO 15537:2022(E)
Principles for selecting and using test persons for testing
anthropometric aspects of industrial products and designs
1 Scope
This document establishes methods for determining the composition of groups of persons whose
an
...