|
SIST EN 848-2:2007+A1:2010/kFprA2:2012
01-junij-2012
9DUQRVWOHVQRREGHORYDOQLKVWURMHY5H]NDOQLNL]YUWHþLPRURGMHP]DHQRVWUDQVNR
REGHODYRGHO(QRYUHWHQVNLUH]NDOQLVWURML]URþQLPPHKDQVNLPSRGDMDQMHP
Safety of woodworking machines - One side moulding machines with rotating tool - Part
2: Single spindle hand fed/integrated fed routing machines
Sicherheit von Holzbearbeitungsmaschinen - Fräsmaschinen für einseitige Bearbeitung
mit drehendem Werkzeug - Teil 2: Einspindelige Oberfräsmaschinen mit
Handvorschub/mechanischem Vorschub
Sécurité des machines pour le travail du bois - Machines à fraiser sur une face à outil
rotatif - Partie 2: Perceuses et défonceuses monobroche à avance manuelle/mécanisée
Ta slovenski standard je istoveten z: EN 848-2:2007+A1:2009/FprA2
ICS:
79.120.10 Lesnoobdelovalni stroji Woodworking machines
SIST EN 848- en,fr,de
2:2007+A1:2010/kFprA2:2012
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 848-2:2007+A1:2010/kFprA2:2012
---------------------- Page: 2 ----------------------
SIST EN 848-2:2007+A1:2010/kFprA2:2012
EUROPEAN STANDARD
FINAL DRAFT
EN 848-2:2007+A1:2009
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA2
April 2012
ICS 79.120.10
English Version
Safety of woodworking machines - One side moulding machines
with rotating tool - Part 2: Single spindle hand fed/integrated fed
routing machines
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungsmaschinen -
fraiser sur une face à outil rotatif - Partie 2: Perceuses et
Fräsmaschinen für einseitige Bearbeitung mit drehendem
défonceuses monobroche à avance manuelle/mécanisée Werkzeug - Teil 2: Einspindelige Oberfräsmaschinen mit
Handvorschub/mechanischem Vorschub
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 142.
This draft amendment A2, if approved, will modify the European Standard EN 848-2:2007+A1:2009. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 848-2:2007+A1:2009/FprA2:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 848-2:2007+A1:2010/kFprA2:2012
EN 848-2:2007+A1:2009/FprA2:2012 (E)
Contents Page
Foreword .4
1 Modifications to Clause 1, Scope .5
2 Modifications to Clause 2, Normative references .5
3 Modification to 3.2, Definitions .6
4 Modifications to Clause 4, List of significant hazards .7
5 Modifications to 5.1, General . 10
6 Modifications to 5.2.1.1, General . 10
7 Modification to 5.2.1.2, Use of well tried components .
...