EN 15163-1:2022

Machines and installations for the exploitation and processing of natural stone - Safety - Part 1: Requirements for stationary diamond wire saws

EN 15163-1:2022

Name:EN 15163-1:2022   Standard name:Machines and installations for the exploitation and processing of natural stone - Safety - Part 1: Requirements for stationary diamond wire saws
Standard number:EN 15163-1:2022   language:English language
Release Date:07-Jun-2022   technical committee:CEN/TC 151 - Construction equipment and building material machines - Safety
Drafting committee:CEN/TC 151/WG 11 - Machines and plants for mining and tooling of natural stone - Safety   ICS number:73.120 - Equipment for processing of minerals

SLOVENSKI STANDARD
01-september-2022
Nadomešča:
SIST EN 15163:2017
Stroji in oprema za pridobivanje in obdelavo naravnega kamna - Varnost - 1. del:
Zahteve za nepremične enožične diamantne žage
Machines and installations for the exploitation and processing of natural stone - Safety -
Part 1: Requirements for stationary diamond wire saws
Maschinen und Anlagen zur Gewinnung und Bearbeitung von Naturstein - Sicherheit -
Teil 1: Anforderungen für stationäre Diamantseilsägen
Machines et installations pour l’exploitation et la transformation de la pierre naturelle -
Sécurité - Partie 1 : Prescriptions pour les scies à fil diamanté fixes
Ta slovenski standard je istoveten z: EN 15163-1:2022
ICS:
25.100.40 Žagni listi Saws
73.120 Oprema za predelavo rudnin Equipment for processing of
minerals
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

EN 15163-1
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2022
EUROPÄISCHE NORM
ICS 73.120 Supersedes EN 15163:2017
English Version
Machines and installations for the exploitation and
processing of natural stone - Safety - Part 1: Requirements
for stationary diamond wire saws
Machines et installations pour l'exploitation et la Maschinen und Anlagen zur Gewinnung und
transformation de la pierre naturelle - Sécurité - Partie Bearbeitung von Naturstein - Sicherheit - Teil 1:
1 : Prescriptions pour les scies à fil diamanté fixes Anforderungen für stationäre Diamantseilsägen
This European Standard was approved by CEN on 27 March 2022.

CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this
European Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by
translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 15163-1:2022 E
worldwide for CEN national Members.

Contents Page
European foreword . 4
Introduction . 5
1 Scope . 6
2 Normative references . 6
3 Terms and definitions . 8
4 Safety requirements and/or protective/risk reduction measures . 16
4.1 General . 16
4.2 Controls . 17
4.2.1 Safety and reliability of control systems . 17
4.2.2 Position of controls . 17
4.2.3 Starting . 18
4.2.4 Normal stop . 18
4.2.5 Emergency stop . 19
4.2.6 Mode selection . 19
4.2.7 Failure of power supply . 20
4.3 Protection against mechanical hazards . 21
4.3.1 Transport of the machine . 21
4.3.2 Installation and stability of machine . 21
4.3.3 Prevention of access to moving parts . 21
4.3.4 Safeguards to minimize the effect of ejection . 23
4.4 Protections against no mechanical hazards . 27
4.4.1 Fire. 27
4.4.2 Noise . 28
4.4.3 Electrical hazards . 28
4.4.4 Ergonomics and handling . 29
4.4.5 Hydraulic and pneumatic components . 29
4.4.6 Electromagnetic compatibility . 29
4.4.7 Laser radiation . 30
4.4.8 Isolation from energy sources . 30
4.4.9 Hazardous materials and substances . 30
4.4.10 Risk of slipping, tripping or falling . 30
4.4.11 Lightning . 34
4.4.12 Maintenance . 34
5 Information for use . 34
5.1 General . 34
5.2 Signals and warning devices . 34
5.3 Marking, signs and written warnings . 34
5.4 Instruction handbook . 35
5.4.1 General . 35
5.4.2 Operator’s instruction . 35
5.4.3 Maintenance instruction . 38
Annex A (informative) List of significant hazards . 40
Annex B (normative) Noise test code . 43
B.1 Introduction . 43
B.2 Measurement of the A-weighted emission sound pressure level at the operator's
positions or other specified positions . 43
B.2.1 Basic standards . 43
B.2.2 Measurement procedure and positions . 43
B.2.3 Measurement uncertainty . 44
B.3 Determination of A-weighted sound-power level. 44
B.3.1 Measurement procedure and positions . 44
B.4 Installation, mounting and operating conditions for noise emission measurement . 44
B.5 Information to be recorded and reported . 45
B.6 Declaration and verification of noise emission values . 47
B.6.1 General . 47
B.6.2 Example of a declaration of noise emission values in the instruction handbook for
stationary diamond wire saws . 48
Annex C (informative) Types of granites for noise test measurement . 53
Annex D (normative) Rigid guards on stationary diamond wire saws-- Impact test method . 56
D.1 General . 56
D.2 Test method . 56
D.2.1 Preliminary remarks . 56
D.2.2 Testing equipment . 56
D.2.2.1 General . 56
D.2.2.2 Projectiles . 56
D.2.2.3 Sampling and supporting the guard under test . 57
D.2.3 Test procedure . 57
D.3 Results . 57
D.4 Assessment. 58
D.5 Test report . 58
D.6 Example of propulsion device for impact test . 58
Annex ZA (informative) Relationship between this European Standard and the essential
requirements of Directive 2006/42/EC aimed to be covered . 60
Bibliography . 63

European foreword
This document (EN 15163-1:2022) has been prepared by Technical Committee CEN/TC 151
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27