|
SIST EN 1279-5:2005/kFprA2:2010
01-januar-2010
Steklo v gradbeništvu - Izolacijsko steklo - 5. del: Ovrednotenje skladnosti
Glass in building - Insulating glass units - Part 5: Evaluation of conformity
Glas im Bauwesen - Mehrscheiben-Isolierglas - Teil 5: Konformitätsbewertung
Verre dans la construction - Vitrage isolant préfabriqué scellé - Partie 5: Évaluation de la
conformité
Ta slovenski standard je istoveten z: EN 1279-5:2005/FprA2
ICS:
81.040.20 Steklo v gradbeništvu Glass in building
SIST EN 1279-5:2005/kFprA2:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 1279-5:2005/kFprA2:2010
---------------------- Page: 2 ----------------------
SIST EN 1279-5:2005/kFprA2:2010
EUROPEAN STANDARD
FINAL DRAFT
EN 1279-5:2005
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA2
November 2009
ICS 81.040.20
English Version
Glass in building - Insulating glass units - Part 5: Evaluation of
conformity
Verre dans la construction - Vitrage isolant préfabriqué Glas im Bauwesen - Mehrscheiben-Isolierglas - Teil 5:
scellé - Partie 5: Évaluation de la conformité Konformitätsbewertung
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 129.
This draft amendment A2, if approved, will modify the European Standard EN 1279-5:2005+A1:2008. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 1279-5:2005/FprA2:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 1279-5:2005/kFprA2:2010
EN 1279-5:2005/FprA2:2009 (E)
Contents Page
Foreword .3
1 Modification to 5.2.1, General .4
2 Addition of a new Annex A .4
3 Modification to Annex ZA .6
2
---------------------- Page: 4 ----------------------
SIST EN 1279-5:2005/kFprA2:2010
EN 1279-5:2005/FprA2:2009 (E)
Foreword
This document (EN 1279-5:2005/FprA2:2009) has been prepared by Technical Committee CEN/TC 129
“Glass in building”, the secretariat of which is held by NBN.
This document is currently submitted to the Unique Acceptance Procedure.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
3
---------------------- Page: 5 ----------------------
SIST EN 1279-5:2005/kFprA2:2010
EN 1279-5:2005/FprA2:2009 (E)
1 Modification to 5.2.1, General
Add as a fourth indent: "
use of ‘other party ITT results’; in accordance with Annex A (normative);".
2 Addition of a new Annex A
Add the following new Annex A: "
Annex A
(normative)
Rules for the use of ‘other party ITT results'
A.1 General
An IGU manufacturer may use ITT results obtained by a third party, e.g. other manufacturer, system
developer, etc., to justify their conformity with this European Standard, i.e. EN 1279-5:2005, 5.2.2, for a
product manufactured to the same design. This data
...