prEN 1506

Ventilation for buildings - Sheet metal air ducts and fittings with circular cross-section - Dimensions

prEN 1506

Name:prEN 1506   Standard name:Ventilation for buildings - Sheet metal air ducts and fittings with circular cross-section - Dimensions
Standard number:prEN 1506   language:English language
Release Date:   technical committee:CEN/TC 156 - Ventilation for buildings
Drafting committee:CEN/TC 156/WG 3 - Ductwork   ICS number:
SLOVENSKI OSIST prEN 1506:2004

PREDSTANDARD
oct 2004
Ventilation for buildings - Sheet metal air ducts and fittings with circular cross-
section - Dimensions
ICS 91.140.30 Referenčna številka
OSIST prEN 1506:2004(en)
©  Standard je založil in izdal Slovenski inštitut za standardizacijo. Razmnoževanje ali kopiranje celote ali delov tega dokumenta ni dovoljeno

---------------------- Page: 1 ----------------------
EUROPEAN STANDARD
DRAFT
prEN 1506
NORME EUROPÉENNE

EUROPÄISCHE NORM

August 2004
ICS  Will supersede EN 1506:1997
English version
Ventilation for buildings - Sheet metal air ducts and fittings with
circular cross-section - Dimensions
Ventilation des bâtiments - Conduits en tôle et accessoires
à section circulaire - Dimensions
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 156.

If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.

This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the Management Centre has the same
status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Cyprus, Czech Republic, Denmark, Estonia, Finland, France,
Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Slovakia,
Slovenia, Spain, Sweden, Switzerland and United Kingdom.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: rue de Stassart, 36  B-1050 Brussels
© 2004 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1506:2004: E
worldwide for CEN national Members.

---------------------- Page: 2 ----------------------
prEN 1506:2004 (E)
Contents Page
Foreword. 3
Introduction . 5
1 Scope. 6
2 Normative references . 6
3 Definitions and symbols. 6
4 Dimensions and values for ducts. 8
5 Dimensions for fittings. 9
6 Tolerances and clearances . 16
Annex A (informative) Examples of alternative designs of ends and connectors. 19
Bibliography . 21

2

---------------------- Page: 3 ----------------------
prEN 1506:2004 (E)
Foreword
This document has been prepared by Technical Committee CEN/TC 156 "Ventilation for buildings",
the secretariat of which is held by BSI.
This document is currently submitted to the CEN Enquiry.
This document will supersede EN 1442:1998.
This document has been prepared under a mandate given to CEN by the European Commission and
the European Free Trade Association, and supports essential requirements of EU Directive(s).
This standard is one of a series of standards for ductwork used for ventilation and air conditioning of
buildings for human occupancy, and it has a parallel standard referring to dimensions of rectangular
ducts.
The position of this standard in the field of mechanical building services is shown in Figure 1.
3

---------------------- Page: 4 ----------------------
prEN 1506:2004 (E)
Mechanical Building Services






Control systems  Ventilation and air conditioning  Heating systems
  systems


...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27