|
SIST EN ISO 15874-3:2004/kprA1:2009
01-junij-2009
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY]DQDSHOMDYH]YURþRLQKODGQRYRGR
3ROLSURSLOHQ33GHO)LWLQJL'RSROQLOR,62)'$0
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 3:
Fittings - Amendment 1 (ISO 15874-3:2003/FDAM 1:2009)
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Polypropylen
(PP) - Teil 3: Formstücke (Änderung von ISO 15874-3:2003) (ISO 15874-3:2003/FDAM
1:2009)
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide -
Polypropylène (PP) - Partie 3: Raccords - Amendement 1 (ISO 15874-3:2003/FDAM
1:2009)
Ta slovenski standard je istoveten z: EN ISO 15874-3:2003/FprA1
ICS:
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
91.140.60 Sistemi za oskrbo z vodo Water supply systems
SIST EN ISO 15874-3:2004/kprA1:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 15874-3:2004/kprA1:2009
---------------------- Page: 2 ----------------------
SIST EN ISO 15874-3:2004/kprA1:2009
EUROPEAN STANDARD
FINAL DRAFT
EN ISO 15874-3:2003
NORME EUROPÉENNE
EUROPÄISCHE NORM
FprA1
March 2009
ICS 23.040.45; 91.140.60
English Version
Plastics piping systems for hot and cold water installations -
Polypropylene (PP) - Part 3: Fittings - Amendment 1 (ISO
15874-3:2003/FDAM 1:2009)
Systèmes de canalisations en plastique pour les
installations d'eau chaude et froide - Polypropylène (PP) -
Partie 3: Raccords - Amendement 1 (ISO 15874-
3:2003/FDAM 1:2009)
This draft amendment is submitted to CEN members for unique acceptance procedure. It has been drawn up by the Technical Committee
CEN/TC 155.
This draft amendment A1, if approved, will modify the European Standard EN ISO 15874-3:2003. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15874-3:2003/FprA1:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 15874-3:2004/kprA1:2009
EN ISO 15874-3:2003/FprA1:2009 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 15874-3:2004/kprA1:2009
EN ISO 15874-3:2003/FprA1:2009 (E)
Foreword
This document (EN ISO 15874-3:2003/FprA1:2009) has been prepared by Technical Committee CEN/TC 155
“Plastics piping systems and ducting systems", the secretariat of which is held by NEN, in collaboration with
Technical Committee ISO/TC 138 "Plastics pipes, fittings and valves for the transport of fluids".
This document is currently submitted to the Unique Acceptance Procedure.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 15874-3:2004/kprA1:2009
---------------------- Page: 6 ----------------------
SIST EN ISO 15874-3:2004/kprA1:2009
FINAL ISO
AMENDMENT
DRAFT 15874-3:2003
FDAM 1
ISO/TC 138/SC 2
Plastics piping systems for hot and cold
Secretariat: SNV
water installations —
Voting begins on:
Polypropylene (PP) —
2009-03-26
Part 3:
Voting terminates on:
2009-05-26
Fittings
AMENDMENT 1
Systèmes de canalisations en plastique pour les installations d'eau
chaude et froide — Polypropylène (PP) —
Partie 3: Raccords
AMENDEMENT 1
Please see the administrative notes on page iii
RECIPIENTS OF THIS DRAFT ARE INVITED TO
SUBMIT, WITH THEIR COMMENTS, NOTIFICATION
OF ANY RELEVANT PATENT RIGHTS OF WHICH
THEY ARE AWARE AND TO PROVIDE SUPPOR
...