|
SIST EN ISO 1302:2004/oprA2:2010
01-oktober-2010
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND2]QDþHYDQMHSRYUãLQVNLKWHNVWXUY
WHKQLãNLGHODYQLãNLGRNXPHQWDFLMLL]GHOND'RSROQLOR 2]QDþHYDQMH]DKWHYY
]YH]L]PDWHULDOQLPGHOHåHP ,62 '$0
Geometrical Product Specifications (GPS) - Indication of surface texture in technical
product documentation - Amendment 2: Indication of material ratio requirements (ISO
1302:2002/DAM 2:2010)
Geometrische Produktspezifikation (GPS) - Angabe der Oberflächenbeschaffenheit in
technischen Produktdokumentationen - Änderung 2: Angabe der Anforderungen an den
Materialanteil (ISO 1302:2002/DAM 2:2010)
Spécification géométrique des produits (GPS) - Indication des états de surface dans la
documentation technique de produits - Amendement 2: Indication des exigences pour le
taux de longueur portante (ISO 1302:2002/DAM 2:2010)
Ta slovenski standard je istoveten z: EN ISO 1302:2002/prA2
ICS:
01.110 7HKQLþQDGRNXPHQWDFLMD]D Technical product
L]GHONH documentation
17.040.20 Lastnosti površin Properties of surfaces
SIST EN ISO 1302:2004/oprA2:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 1302:2004/oprA2:2010
---------------------- Page: 2 ----------------------
SIST EN ISO 1302:2004/oprA2:2010
EUROPEAN STANDARD
DRAFT
EN ISO 1302:2002
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA2
July 2010
ICS 17.040.20; 01.100.20
English Version
Geometrical Product Specifications (GPS) - Indication of surface
texture in technical product documentation - Amendment 2:
Indication of material ratio requirements (ISO 1302:2002/DAM
2:2010)
Spécification géométrique des produits (GPS) - Indication Geometrische Produktspezifikation (GPS) - Angabe der
des états de surface dans la documentation technique de Oberflächenbeschaffenheit in technischen
produits - Amendement 2: Indication des exigences pour le Produktdokumentationen - Änderung 2: Angabe der
taux de longueur portante (ISO 1302:2002/DAM 2:2010) Anforderungen an den Materialanteil (ISO 1302:2002/DAM
2:2010)
This draft amendment is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee CEN/TC 290.
This draft amendment A2, if approved, will modify the European Standard EN ISO 1302:2002. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 1302:2002/prA2:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 1302:2004/oprA2:2010
EN ISO 1302:2002/prA2:2010 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 1302:2004/oprA2:2010
EN ISO 1302:2002/prA2:2010 (E)
Foreword
This document (EN ISO 1302:2002/prA2:2010) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of
which is held by AFNOR.
This document is currently submitted to the parallel Enquiry.
Endorsement notice
The text of ISO 1302:2002/DAM 2:2010 has been approved by CEN as a EN ISO 1302:2002/prA2:2010
wi
...