|
kSIST-TP FprCEN/TR 1451-2:2010
01-junij-2010
Cevni sistemi iz polimernih materialov za nizko- in visokotemperaturne odvodne
sisteme v zgradbah - Polipropilen (PP) - 2. del: Navodilo za ugotavljanje skladnosti
Plastics piping systems for soil and waste discharge (low and high temperature) within
the building structure - Polypropylene (PP) - Part 2: Guidance for the assessment of
conformity
Kunststoff-Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hoher
Temperatur) innerhalb der Gebäudestruktur - Polypropylen (PP) - Teil 2: Empfehlungen
für die Beurteilung der Konformität
Systèmes de canalisations en plastique pour l'évacuation des eaux-vannes et des eaux
usées (à basse et à haute température) à l'intérieur de la structure des bâtiments -
Polypropylène (PP) - Partie 2: Guide pour l'évaluation de la conformité
Ta slovenski standard je istoveten z: FprCEN/TR 1451-2
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.80 Drenažni sistemi Drainage systems
kSIST-TP FprCEN/TR 1451-2:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
kSIST-TP FprCEN/TR 1451-2:2010
---------------------- Page: 2 ----------------------
kSIST-TP FprCEN/TR 1451-2:2010
TECHNICAL REPORT
FINAL DRAFT
FprCEN/TR 1451-2
RAPPORT TECHNIQUE
TECHNISCHER BERICHT
April 2010
ICS 23.040.20; 91.140.80 Will supersede ENV 1451-2:2001
English Version
Plastics piping systems for soil and waste discharge (low and
high temperature) within the building structure - Polypropylene
(PP) - Part 2: Guidance for the assessment of conformity
Systèmes de canalisations en plastique pour l'évacuation Kunststoff-Rohrleitungssysteme zum Ableiten von
des eaux-vannes et des eaux usées (à basse et à haute Abwasser (niedriger und hoher Temperatur) innerhalb der
température) à l'intérieur de la structure des bâtiments - Gebäudestruktur - Polypropylen (PP) - Teil 2:
Polypropylène (PP) - Partie 2: Guide pour l'évaluation de la Empfehlungen für die Beurteilung der Konformität
conformité
This draft Technical Report is submitted to CEN members for Technical Committee Approval. It has been drawn up by the Technical
Committee CEN/TC 155.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Warning : This document is not a Technical Report. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a Technical Report.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. FprCEN/TR 1451-2:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
kSIST-TP FprCEN/TR 1451-2:2010
FprCEN/TR 1451-2:2010 (E)
Contents Page
Foreword .3
Introduction .4
1 Scope .5
2 Normative references .5
3 Terms and definitions .5
4 Abbreviated terms .8
5 General .8
6 Testing and inspection .8
6.1 Material specification .8
6.2 Grouping .9
6.2.1 General .
...