|
SLOVENSKI STANDARD
01-september-2022
Cevni sistemi iz polimernih materialov za napeljave z vročo in hladno vodo -
Polipropilen (PP) - 2. del: Cevi - Dopolnilo A2 (ISO 15874-2:2013/Amd 2:2022)
Plastics piping systems for hot and cold water installations - Polypropylene (PP) - Part 2:
Pipes - Amendement 2: Impact test (ISO 15874-2:2013/Amd 2:2022)
Kunststoff-Rohrleitungssysteme für die Warm- und Kaltwasserinstallation - Polypropylen
(PP) - Teil 2: Rohre - Änderung 2: Kerbschlagzähigkeitsprüfung (ISO 15874-2:2013/Amd
2:2022)
Systèmes de canalisations en plastique pour les installations d'eau chaude et froide -
Polypropylène (PP) - Partie 2: Tubes - Amendement 2 (ISO 15874-2:2013/Amd 2:2022)
Ta slovenski standard je istoveten z: EN ISO 15874-2:2013/A2:2022
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.60 Sistemi za oskrbo z vodo Water supply systems
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
EN ISO 15874-2:2013/A2
EUROPEAN STANDARD
NORME EUROPÉENNE
June 2022
EUROPÄISCHE NORM
ICS 23.040.20; 91.140.60
English Version
Plastics piping systems for hot and cold water installations
- Polypropylene (PP) - Part 2: Pipes - Amendement 2:
Impact test (ISO 15874-2:2013/Amd 2:2022)
Systèmes de canalisations en plastique pour les Kunststoff-Rohrleitungssysteme für die Warm- und
installations d'eau chaude et froide - Polypropylène Kaltwasserinstallation - Polypropylen (PP) - Teil 2:
(PP) - Partie 2: Tubes - Amendement 2 (ISO 15874- Rohre - Änderung 2: Kerbschlagzähigkeitsprüfung (ISO
2:2013/Amd 2:2022) 15874-2:2013/Amd 2:2022)
This amendment A2 modifies the European Standard 2841667; it was approved by CEN on 19 June 2022.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of
this amendment into the relevant national standard without any alteration. Up-to-date lists and bibliographical references
concerning such national standards may be obtained on application to the CEN-CENELEC Management Centre or to any CEN
member.
This amendment exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 15874-2:2013/A2:2022 E
worldwide for CEN national Members.
Contents Page
European foreword . 3
European foreword
This document (EN ISO 15874-2:2013/A2:2022) has been prepared by Technical Committee ISO/TC
138 "Plastics pipes, fittings and valves for the transport of fluids" in collaboration with Technical
Committee CEN/TC 155 “Plastics piping systems and ducting systems” the secretariat of which is held
by NEN.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by December 2022, and conflicting national standards
shall be withdrawn at the latest by December 2022.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN shall not be held responsible for identifying any or all such patent rights.
Any feedback and questions on this document should be directed to the users’ national standards
body/national committee. A complete listing of these bodies can be found on the CEN website.
According to the CEN-CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Croatia, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Republic of
North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and the
United Kingdom.
Endorsement notice
The text of ISO 15874-2:2013/Amd 2:2022 has been approved by CEN as EN ISO 15874-
2:2013/A2:2022 without any modification.
INTERNATIONAL ISO
STANDARD 15874-2
Second edition
2013-02-15
AMENDMENT 2
2022-06
Plastics piping systems for hot
and cold water installations —
Polypropylene (PP) —
Part 2:
Pipes
AMENDMENT 2: Impact test
Systèmes de canalisations en plastique pour les installations d'eau
chaude et froide — Polypropylène (PP) —
Partie 2: Tubes
AMENDEMENT 2: Essai de choc
Reference number
ISO 15874-2:2013/Amd.2:2022(E)
ISO 15874-2:2013/Amd.2:2022(E)
© ISO 2022
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: [email protected]
Website: www.iso.org
Published in Switzerland
ii
--------------
...