|
oSIST prEN 12514-2:2009
01-julij-2009
6HVWDYQLGHOLVLVWHPRY]DGRYRGWHNRþHJDJRULYDROMQLPDSDUDWRPGHO
9DUQRVWQH]DKWHYHLQSUHVNXãDQMH1DSDMDOQHþUSDONHUHJXODFLMVNHLQYDUQRVWQH
QDSUDYHGQHYQLUH]HUYRDUML
Parts for supply systems for demand appliance with liquid fuels - Part 2: Safety
requirements and tests - Feed pumps, control and safety devices, operating vessels
Bauelemente für Versorgungsanlagen für Verbrauchsstellen mit flüssigen Brennstoffen -
Teil 2: Sicherheitstechnische Anforderungen und Prüfungen - Förderaggregate, Regel-
und Sicherheitseinrichtungen, Betriebsbehälter, Deutsche Fassung prEN 12514-2:2008
Composants des systèmes d'alimentation pour les brûleurs de combustibles liquides -
Partie 2 : Prescriptions de sécurité et essais -Pompes, dispositifs de régulation et de
sécurité, réservoirs
Ta slovenski standard je istoveten z: prEN 12514-2 rev
ICS:
27.060.10 *RULOQLNLQDWHNRþHLQWUGR Liquid and solid fuel burners
JRULYR
oSIST prEN 12514-2:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 12514-2:2009
---------------------- Page: 2 ----------------------
oSIST prEN 12514-2:2009
EUROPEAN STANDARD
DRAFT
prEN 12514-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2009
ICS 27.060.10 Will supersede EN 12514-1:2000, EN 12514-2:2000
English Version
Parts for supply systems for consuming units with liquid fuels -
Part 2: Safety requirements and tests - Feed pumps, control and
safety devices, service vessels
Appareils et éléments de construction pour le transfert au Bauelemente für Versorgungsanlagen für
consommateur de liquide combustible - Partie 2 : Verbrauchsstellen mit flüssigen Brennstoffen - Teil 2:
Prescriptions de sécurité et essais - Pompes aspirantes et Sicherheitstechnische Anforderungen und Prüfungen -
refoulantes, réservoirs, accumulateurs á membrane, Förderaggregate, Regel- und Sicherheitseinrichtungen,
moyens de côntrole et de mesure Betriebsbehälter
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 47.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12514-2:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 12514-2:2009
prEN 12514-2:2009 (E)
Contents Page
Foreword .4
1 Scope .5
2 Normative references .5
3 Terms and definitions .6
4 Safety requirements .6
4.1 General requirements .6
4.1.1 Materials .6
4.1.2 Constructi
...