|
SIST EN ISO 898-1:2009/oprA1:2010
01-julij-2010
Mehanske lastnosti veznih elementov iz ogljikovega in legiranega jekla - 1. del:
Vijaki s specificiranim trdnostnim razredom - Grobi in fini navoj (ISO 898-
1:2009/DAM 1:2010)
Mechanical properties of fasteners made of carbon steel and alloy steel - Part 1: Bolts,
screws and studs with specified property classes - Coarse thread and fine pitch thread
(ISO 898-1:2009/DAM 1:2010)
Mechanische Eigenschaften von Verbindungselementen aus Kohlenstoffstahl und
legiertem Stahl - Teil 1: Schrauben mit festgelegten Festigkeitsklassen - Regelgewinde
und Feingewinde (ISO 898-1:2009/DAM 1:2010)
Caractéristiques mécaniques des éléments de fixation en acier au carbone et en acier
allié - Partie 1: Vis, goujons et tiges filetées de classes de qualité spécifiées - Filetages à
pas gros et filetages à pas fin (ISO 898-1:2009/DAM 1:2010)
Ta slovenski standard je istoveten z: EN ISO 898-1:2009/prA1
ICS:
21.060.10 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
SIST EN ISO 898-1:2009/oprA1:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 898-1:2009/oprA1:2010
---------------------- Page: 2 ----------------------
SIST EN ISO 898-1:2009/oprA1:2010
EUROPEAN STANDARD
DRAFT
EN ISO 898-1:2009
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
March 2010
ICS 21.060.10
English Version
Mechanical properties of fasteners made of carbon steel and
alloy steel - Part 1: Bolts, screws and studs with specified
property classes - Coarse thread and fine pitch thread (ISO 898-
1:2009/DAM 1:2010)
Caractéristiques mécaniques des éléments de fixation en Mechanische Eigenschaften von Verbindungselementen
acier au carbone et en acier allié - Partie 1: Vis, goujons et aus Kohlenstoffstahl und legiertem Stahl - Teil 1:
tiges filetées de classes de qualité spécifiées - Filetages à Schrauben mit festgelegten Festigkeitsklassen -
pas gros et filetages à pas fin (ISO 898-1:2009/DAM Regelgewinde und Feingewinde (ISO 898-1:2009/DAM
1:2010) 1:2010)
This draft amendment is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee CEN/TC 185.
This draft amendment A1, if approved, will modify the European Standard EN ISO 898-1:2009. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 898-1:2009/prA1:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 898-1:2009/oprA1:2010
EN ISO 898-1:2009/prA1:2010 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 898-1:2009/oprA1:2010
EN ISO 898-1:2009/prA1:2010 (E)
Foreword
This document (EN ISO 898-1:2009/prA1:2010) has been prepared by Technical Committee ISO/TC 2
"Fasteners" in collaboration with Technical Committee CEN/TC 185 “Fasteners” the secretariat of which is
held by DIN.
This document is currently submitted to the parallel Enquiry.
Endorsement notice
The text of ISO 898-1:2009/DAM 1:2010 has been approved by CEN as a EN ISO 898-1:2009/prA1:2010
without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 898-1:2009/oprA1:2010
---------------------- Page:
...