prEN 1807-2

Safety of woodworking machines - Band sawing machines - Part 2: Log sawing machines

prEN 1807-2

Name:prEN 1807-2   Standard name:Safety of woodworking machines - Band sawing machines - Part 2: Log sawing machines
Standard number:prEN 1807-2   language:English language
Release Date:09-Jan-2012   technical committee:CEN/TC 142 - Woodworking machines - Safety
Drafting committee:CEN/TC 142/WG 3 - Bandsawing machines   ICS number:79.120.10 - Woodworking machines
SLOVENSKI STANDARD
oSIST prEN 1807-2:2009
01-junij-2009
9DUQRVWOHVQRREGHORYDOQLKVWURMHY7UDþQHåDJHGHOäDJH]DUD]UH]KORGRYLQH
Safety of woodworking machines - Band sawing machines - Part 2: Log sawing
machines
Sicherheit von Holzbearbeitungdmaschinen - Bandsägemaschinen - Teil 2:
Logbandsäge
Sécurité des machines pour le travail du bois - Machines à scier à ruban - Partie 2: Scies
à grumes
Ta slovenski standard je istoveten z: prEN 1807-2
ICS:
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
oSIST prEN 1807-2:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
oSIST prEN 1807-2:2009

---------------------- Page: 2 ----------------------
oSIST prEN 1807-2:2009
EUROPEAN STANDARD
DRAFT
prEN 1807-2
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2009
ICS 79.120.10 Will supersede EN 1807:1999
English Version
Safery of woodworking machines - Band sawing machines - Part
2: Log sawing machines
Sécurité des machines pour le travail du bois - Machines à Sicherheit von Holzbearbeitungdmaschinen -
scier à ruban - Partie 2: Scies à grumes Bandsägemaschinen - Teil 2: Logbandsäge
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 142.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1807-2:2009: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
oSIST prEN 1807-2:2009
prEN 1807-2:2009 (E)
Contents Page
Foreword .4
Introduction .5
1 Scope .5
2 Normative references .6
3 Terms and definitions .8
3.1 General .8
3.2 Definitions .8
3.3 Terminology . 11
4 List of significant hazards . 14
5 Safety requirements and/or measures . 18
5.1 General . 18
5.2 Controls . 18
5.2.1 Safety and reliability of control
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27