|
oSIST prEN 1807-1:2009
01-junij-2009
9DUQRVWOHVQRREGHORYDOQLKVWURMHY7UDþQHåDJHGHO 1DPL]QHWUDþQHåDJHLQ
åDJH]DUH]DQMHGHVN
Safety of woodworking machines - Band sawing machines - Part 1: Table band saws and
band re-saws
Sicherheit von Holzbearbeitungsmaschinen - Bandsägemaschinen - Teil 1:
Tischbandsägemaschinen und Trennbandsägemaschinen
Sécurité des machines pour le travail du bois - Scies à ruban - Partie 1: Scies à ruban à
table et scies à refendre
Ta slovenski standard je istoveten z: prEN 1807-1
ICS:
25.080.60 Strojne žage Sawing machines
79.120.10 Lesnoobdelovalni stroji Woodworking machines
oSIST prEN 1807-1:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 1807-1:2009
---------------------- Page: 2 ----------------------
oSIST prEN 1807-1:2009
EUROPEAN STANDARD
DRAFT
prEN 1807-1
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2009
ICS 79.120.10 Will supersede EN 1807:1999
English Version
Safety of woodworking machines - Band sawing machines - Part
1: Table band saws and band re-saws
Sécurité des machines pour le travail du bois - Scies à Sicherheit von Holzbearbeitungsmaschinen -
ruban - Partie 1: Scies à ruban à table et scies à refendre Bandsägemaschinen - Teil 1: Tischbandsägemaschinen
und Trennbandsägemaschinen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 142.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1807-1:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 1807-1:2009
prEN 1807-1:2009 (E)
Contents Page
Foreword .4
Introduction .5
1 Scope .5
2 Normative references .6
3 Terms and definitions .8
3.1 General .8
3.2 Definitions .8
3.3 Terminology . 11
4 List of significant hazards . 15
5 Safety requirements and/or measures . 18
5.1 General . 18
5.2 Controls .
...