|
oSIST prEN 15013:2011
01-junij-2011
Cevni sistemi iz polimernih materialov - Podzemne cevne komponente za
odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu - Zahteve in
preskusi/metode ocenjevanja za cevi in fitinge
Plastics piping systems - Non-pressure drainage and sewerage piping components
buried in ground - Requirements and test/assessment methods for pipes and fittings
Kunststoff-Rohrleitungssysteme - Drucklose Rohrleitungssysteme für erdverlegte
Abwasserkanäle und -leitungen - Anforderungen und Prüf /Bewertungsverfahren für
Rohre und Formstücke
Systèmes de canalisations en plastique - Composants de canalisations enterrés pour
assainissement sans pression - Exigences et méthodes d'essai/d'évaluation pour tubes
et raccords
Ta slovenski standard je istoveten z: prEN 15013
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
oSIST prEN 15013:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 15013:2011
---------------------- Page: 2 ----------------------
oSIST prEN 15013:2011
EUROPEAN STANDARD
DRAFT
prEN 15013
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2011
ICS 93.030
English Version
Plastics piping systems - Non-pressure drainage and sewerage
piping components buried in ground - Requirements and
test/assessment methods for pipes and fittings
Systèmes de canalisations en plastique - Composants de Kunststoff-Rohrleitungssysteme - Drucklose
canalisations enterrés pour assainissement sans pression - Rohrleitungssysteme für erdverlegte Abwasserkanäle und -
Exigences et méthodes d'essai/d'évaluation pour tubes et leitungen - Anforderungen und Prüf /Bewertungsverfahren
raccords für Rohre und Formstücke
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 155.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15013:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 15013:2011
prEN 15013:2011 (E)
Contents Page
Foreword .4
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms and definitions .7
4 Requirements .7
4.1 Reaction to fire .7
4.2 Maximum load for admissible deformation .
...