|
oSIST prEN 15015:2011
01-junij-2011
&HYQLVLVWHPLL]SROLPHUQLKPDWHULDORY&HYQHNRPSRQHQWH]DYURþRLQKODGQR
YRGR=DKWHYHLQSUHVNXVLPHWRGHRFHQMHYDQMD]DFHYLLQILWLQJH
Plastics piping systems - Hot and cold water piping components - Requirements and
test/assessment methods for pipes and fittings
Kunststoff-Rohrleitungssysteme - Bauteile für den Einsatz in Rohrleitungen für Warm-
und Kaltwasser - Anforderungen und Prüf /Bewertungsverfahren für Rohre und
Formstücke
Systèmes de canalisations en plastique - Composants de canalisations pour eau chaude
et froide non destinée à la consommation humaine - Exigences et méthodes
d'essais/d'évaluation pour tubes et raccords
Ta slovenski standard je istoveten z: prEN 15015
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
91.140.60 Sistemi za oskrbo z vodo Water supply systems
oSIST prEN 15015:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 15015:2011
---------------------- Page: 2 ----------------------
oSIST prEN 15015:2011
EUROPEAN STANDARD
DRAFT
prEN 15015
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2011
ICS 23.040.01 Will supersede EN 15015:2007
English Version
Plastics piping systems - Hot and cold water piping components
- Requirements and test/assessment methods for pipes and
fittings
Systèmes de canalisations en plastique - Composants de Kunststoff-Rohrleitungssysteme - Bauteile für den Einsatz
canalisations pour eau chaude et froide non destinée à la in Rohrleitungen für Warm- und Kaltwasser -
consommation humaine - Exigences et méthodes Anforderungen und Prüf /Bewertungsverfahren für Rohre
d'essais/d'évaluation pour tubes et raccords und Formstücke
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 155.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15015:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 15015:2011
prEN 15015:2011 (E)
Contents Page
Foreword .4
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms and definitions .7
4 Requirements .8
4.1 Reaction to fire .8
4.2 Internal pressure strength .
...