|
oSIST prEN 15012:2011
01-junij-2011
Cevni sistemi iz polimernih materialov - Odvodne cevne komponente brez tlaka v
zgradbah - Zahteve in preskusi/metode ocenjevanja za cevi in fitinge
Plastics piping systems - Non pressure soil and waste discharge piping components
within the building structure - Requirements and test/assessment methods for pipes and
fittings
Kunststoff-Rohrleitungssysteme - Drucklose Rohrleitungssysteme zum Ableiten von
Abwasser innerhalb der Gebäudestruktur - Anforderungen und Prüf
-/Bewertungsverfahren für Rohre und Formstücke
Systèmes de canalisations en plastique - Composants de canalisations pour l'évacuation
des eaux-vannes et des eaux usées à l'intérieur de la structure des bâtiments -
Exigences et méthodes d'essai/d'évaluation pour tubes et raccords
Ta slovenski standard je istoveten z: prEN 15012
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
91.140.80 Drenažni sistemi Drainage systems
oSIST prEN 15012:2011 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 15012:2011
---------------------- Page: 2 ----------------------
oSIST prEN 15012:2011
EUROPEAN STANDARD
DRAFT
prEN 15012
NORME EUROPÉENNE
EUROPÄISCHE NORM
March 2011
ICS 91.140.80 Will supersede EN 15012:2007
English Version
Plastics piping systems - Non pressure soil and waste discharge
piping components within the building structure - Requirements
and test/assessment methods for pipes and fittings
Systèmes de canalisations en plastique - Composants de Kunststoff-Rohrleitungssysteme - Drucklose
canalisations pour l'évacuation des eaux-vannes et des Rohrleitungssysteme zum Ableiten von Abwasser innerhalb
eaux usées à l'intérieur de la structure des bâtiments - der Gebäudestruktur - Anforderungen und Prüf-
Exigences et méthodes d'essai/d'évaluation pour tubes et /Bewertungsverfahren für Rohre und Formstücke
raccords
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 155.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2011 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15012:2011: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 15012:2011
prEN 15012:2011 (E)
Contents Page
Foreword . 3
Introduction . 3
1 Scope . 4
2 Normative references . 4
3 Terms, definitions and symbols . 5
4 Requirements . 6
4.1 Reaction to fire .
...