|
SIST EN ISO 5436-2:2004/oprA1:2010
01-oktober-2010
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND7HNVWXUDSRYUãLQH SURILOQDPHWRGD
VWDQGDUGL]DPHULOQRRSUHPRGHO 6WDQGDUGL]DPHULOQRSURJUDPVNRRSUHPR
'RSROQLOR ,62 '$0
Geometrical Product Specifications (GPS) - Surface texture: Profile method;
Measurement standards - Part 2: Software measurement standards - Amendment 1 (ISO
5436-2:2001/DAM 1:2010)
Geometrische Produktspezifikation (GPS) - Oberflächenbeschaffenheit:
Tastschnittverfahren; Normale - Teil 2: Software-Normale (ISO 5436-2:2001/DAM
1:2010)
Spécification géométrique des produits (GPS) - État de surface: Méthode du profil;
Étalons - Partie 2: Étalons logiciels - Amendement 1 (ISO 5436-2:2001/DAM 1:2010)
Ta slovenski standard je istoveten z: EN ISO 5436-2:2001/prA1
ICS:
17.040.30 Merila Measuring instruments
SIST EN ISO 5436-2:2004/oprA1:2010 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 5436-2:2004/oprA1:2010
---------------------- Page: 2 ----------------------
SIST EN ISO 5436-2:2004/oprA1:2010
EUROPEAN STANDARD
DRAFT
EN ISO 5436-2:2001
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
July 2010
ICS 17.040.30
English Version
Geometrical Product Specifications (GPS) - Surface texture:
Profile method; Measurement standards - Part 2: Software
measurement standards - Amendment 1 (ISO 5436-2:2001/DAM
1:2010)
Spécification géométrique des produits (GPS) - État de
surface: Méthode du profil; Étalons - Partie 2: Étalons
logiciels - Amendement 1 (ISO 5436-2:2001/DAM 1:2010)
This draft amendment is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee CEN/TC 290.
This draft amendment A1, if approved, will modify the European Standard EN ISO 5436-2:2001. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same
status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 5436-2:2001/prA1:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 5436-2:2004/oprA1:2010
EN ISO 5436-2:2001/prA1:2010 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 5436-2:2004/oprA1:2010
EN ISO 5436-2:2001/prA1:2010 (E)
Foreword
This document (EN ISO 5436-2:2001/prA1:2010) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of
which is held by AFNOR.
This document is currently submitted to the parallel Enquiry.
Endorsement notice
The text of ISO 5436-2:2001/DAM 1:2010 has been approved by CEN as a EN ISO 5436-2:2001/prA1:2010
without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 5436-2:2004/oprA1:2010
---------------------- Page: 6 ----------------------
SIST EN ISO 5436-2:2004/oprA1:2010
DRAFT AMENDMENT ISO 5436-2:2001/DAmd 1
ISO/TC 213 Secretariat: DS
Voting begins on: Voting terminates on:
2010-07-29 2010-12-29
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION • МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ • ORGANISATION INTERNATIONALE DE NORMAL
...