|
oSIST prEN 13175:2010
01-september-2010
2SUHPDLQSULERU]DXWHNRþLQMHQLQDIWQLSOLQ813=DKWHYHLQSUHVNXãDQMH
YHQWLORYLQSULNOMXþNRY]DSRVRGH]DXWHNRþLQMHQLQDIWQLSOLQ813
LPG Equipment and accessories - Specification and testing for Liquefied Petroleum Gas
(LPG) tank valves and fittings
Flüssiggas-Geräte und -Ausrüstungsteile - Spezifikation und Prüfung von Ventilen und
Ausrüstungsteilen von Behältern für Flüssiggas (LPG)
Equipements pour GPL et leurs accessoires - Spécifications et essais des équipements
et accessoires des réservoirs pour gaz de pétrole liquéfié (GPL)
Ta slovenski standard je istoveten z: prEN 13175
ICS:
23.020.10 1HSUHPLþQHSRVRGHLQ Stationary containers and
UH]HUYRDUML tanks
23.060.01 Ventili na splošno Valves in general
75.180.01 Oprema za industrijo nafte in Equipment for petroleum and
zemeljskega plina na splošno natural gas industries in
general
oSIST prEN 13175:2010 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 13175:2010
---------------------- Page: 2 ----------------------
oSIST prEN 13175:2010
EUROPEAN STANDARD
DRAFT
prEN 13175
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2010
ICS 23.060.01 Will supersede EN 13175:2003+A2:2007
English Version
LPG Equipment and accessories - Specification and testing for
Liquefied Petroleum Gas (LPG) tank valves and fittings
Equipements pour GPL et leurs accessoires - Flüssiggas-Geräte und -Ausrüstungsteile - Spezifikation
Spécifications et essais des équipements et accessoires und Prüfung von Ventilen und Ausrüstungsteilen von
des réservoirs pour gaz de pétrole liquéfié (GPL) Behältern für Flüssiggas (LPG)
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 286.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the
same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2010 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 13175:2010: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 13175:2010
prEN 13175:2010 (E)
Contents Page
Foreword .4
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms and definitions .7
4 Operating conditions .9
5 Materials . 10
5.1 Environmental . 10
5.2 General .
...