|
oSIST prEN 16448-3:2012
01-september-2012
9DURYDOQDREOHND1HSUHERMQRREODþLORGHO2GSRUQRVWSURWLYERGX]UH]LORPLQ
ERGDORP]DKWHYHLQSUHVNXVQHPHWRGH
Protective Clothing - Body Armour - Part 3: Knife and Spike Resistance, Requirements
and test methods
Schutzkleidung - Körperschutz - Teil 3: Widerstand gegen Messer und Dorne,
Anforderungen und Prüfverfahren
Vêtement de protection - Protection du corps - Partie 3 : Résistance à couteaus et
broches - exigences et méthodes d'essai
Ta slovenski standard je istoveten z: prEN 16448-3
ICS:
13.340.10 Varovalna obleka Protective clothing
oSIST prEN 16448-3:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 16448-3:2012
---------------------- Page: 2 ----------------------
oSIST prEN 16448-3:2012
EUROPEAN STANDARD
DRAFT
prEN 16448-3
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2012
ICS 13.340.10
English Version
Protective Clothing - Body Armour - Part 3: Knife and Spike
Resistance, Requirements and test methods
Vêtement de protection - Protection du corps - Partie 3 : Schutzkleidung - Körperschutz - Teil 3: Widerstand gegen
Résistance à couteaus et broches - exigences et méthodes Messer und Dorne, Anforderungen und Prüfverfahren
d'essai
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 162.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 16448-3:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 16448-3:2012
prEN 16448-3:2012 (E)
Contents Page
Foreword .5
Introduction .6
1 Scope .7
2 Normative references .7
3 Terms and definitions .7
4 Requirements .7
5 Test methodology .7
5.1 Test equipment .7
5.2 Knife/Spike missile .7
5.3 The engineered test knife and spike .8
5.4 Velocity measurement .9
5.5 The Composite Backing
...