|
SIST EN ISO 14405-1:2012/oprA1:2012
01-oktober-2012
6SHFLILNDFLMDJHRPHWULMVNLKYHOLþLQL]GHOND7ROHUDQFHGLPHQ]LMGHO 'ROåLQVNH
PHUH'RSROQLOR ,62 '$0
Geometrical product specifications (GPS) - Dimensional tolerancing - Part 1: Linear sizes
- Amendment 1 (ISO 14405-1:2010/DAM 1:2012)
Geometrische Produktspezifikation (GPS) - Dimensionelle Tolerierung - Teil 1:
Längenmaße - Änderung 1 (ISO 14405-1:2010/DAM 1:2012)
Spécification géométrique des produits (GPS) - Tolérancement dimensionnel - Partie 1:
Tailles linéaires - Amendement 1 (ISO 14405-1:2010/DAM 1:2012)
Ta slovenski standard je istoveten z: EN ISO 14405-1:2010/prA1
ICS:
17.040.10 Tolerance in ujemi Limits and fits
SIST EN ISO 14405-1:2012/oprA1:2012 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 14405-1:2012/oprA1:2012
---------------------- Page: 2 ----------------------
SIST EN ISO 14405-1:2012/oprA1:2012
EUROPEAN STANDARD
DRAFT
EN ISO 14405-1:2010
NORME EUROPÉENNE
EUROPÄISCHE NORM
prA1
August 2012
ICS 17.040.30
English Version
Geometrical product specifications (GPS) - Dimensional
tolerancing - Part 1: Linear sizes - Amendment 1 (ISO 14405-
1:2010/DAM 1:2012)
Spécification géométrique des produits (GPS) - Geometrische Produktspezifikation (GPS) - Dimensionelle
Tolérancement dimensionnel - Partie 1: Tailles linéaires - Tolerierung - Teil 1: Längenmaße - Änderung 1 (ISO
Amendement 1 (ISO 14405-1:2010/DAM 1:2012) 14405-1:2010/DAM 1:2012)
This draft amendment is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee CEN/TC 290.
This draft amendment A1, if approved, will modify the European Standard EN ISO 14405-1:2010. If this draft becomes an amendment,
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this
amendment into the relevant national standard without any alteration.
This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 14405-1:2010/prA1:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN ISO 14405-1:2012/oprA1:2012
EN ISO 14405-1:2010/prA1:2012 (E)
Contents Page
Foreword .3
2
---------------------- Page: 4 ----------------------
SIST EN ISO 14405-1:2012/oprA1:2012
EN ISO 14405-1:2010/prA1:2012 (E)
Foreword
This document (EN ISO 14405-1:2010/prA1:2012) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of
which is held by AFNOR.
This document is currently submitted to the parallel Enquiry.
Endorsement notice
The text of ISO 14405-1:2010/DAM 1:2012 has been approved by CEN as a EN ISO 14405-1:2010/prA1:2012
without any modification.
3
---------------------- Page: 5 ----------------------
SIST EN ISO 14405-1:2012/oprA1:2012
---------------------- Page: 6 ----------------------
SIST EN ISO 14405-1:2012/oprA1:2012
DRAFT AMENDMENT ISO 14405-1:2010/DAM 1
ISO/TC 213 Secretariat: DS
Voting begins on Voting terminates on
2012-08-09 2013-01-09
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ ORGANISATION INTERNATIONALE DE NOR
...