EN ISO 3040:2012/prA1

Geometrical product specifications (GPS) - Dimensioning and tolerancing - Cones (ISO 3040:2009/DAM 1:2014)

EN ISO 3040:2012/prA1

Name:EN ISO 3040:2012/prA1   Standard name:Geometrical product specifications (GPS) - Dimensioning and tolerancing - Cones (ISO 3040:2009/DAM 1:2014)
Standard number:EN ISO 3040:2012/prA1   language:English language
Release Date:18-May-2014   technical committee:CEN/TC 290 - Dimensional and geometrical product specification and verification
Drafting committee:CEN/TC 290 - Dimensional and geometrical product specification and verification   ICS number:01.100.20 - Mechanical engineering drawings
SLOVENSKI STANDARD
SIST EN ISO 3040:2012/oprA1:2012
01-oktober-2012
Geometrijska specifikacija proizvoda (GPS) - Dimenzioniranje in toleriranje -
Konusi - Dopolnilo 1 (ISO 3040:2009/DAM 1:2012)
Geometrical product specifications (GPS) - Dimensioning and tolerancing - Cones -
Amendment 1 (ISO 3040:2009/DAM 1:2012)
Geometrische Produktspezifikation (GPS) - Maßeintragung und Toleranzfestlegung -
Kegel - Änderung 1 (ISO 3040:2009/DAM 1:2012)
Spécification géométrique des produits (GPS) - Cotation et tolérancement - Cônes -
Amendement 1 (ISO 3040:2009/DAM 1:2012)
Ta slovenski standard je istoveten z: EN ISO 3040:2012/prA1
ICS:
01.100.20 Konstrukcijske risbe Mechanical engineering
drawings
SIST EN ISO 3040:2012/oprA1:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST EN ISO 3040:2012/oprA1:2012

---------------------- Page: 2 ----------------------

SIST EN ISO 3040:2012/oprA1:2012


EUROPEAN STANDARD
DRAFT
EN ISO 3040:2012
NORME EUROPÉENNE

EUROPÄISCHE NORM
prA1
August 2012
ICS 17.040.30
English Version
Geometrical product specifications (GPS) - Dimensioning and
tolerancing - Cones - Amendment 1 (ISO 3040:2009/DAM
1:2012)
Spécification géométrique des produits (GPS) - Cotation et Geometrische Produktspezifikation (GPS) - Maßeintragung
tolérancement - Cônes - Amendement 1 (ISO
und Toleranzfestlegung - Kegel - Änderung 1 (ISO
3040:2009/DAM 1:2012) 3040:2009/DAM 1:2012)
This draft amendment is submitted to CEN members for parallel enquiry. It has been drawn up by the Technical Committee CEN/TC 290.

This draft amendment A1, if approved, will modify the European Standard EN ISO 3040:2012. If this draft becomes an amendment, CEN
members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for inclusion of this amendment
into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other language made
by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management Centre has
the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN ISO 3040:2012/prA1:2012: E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------

SIST EN ISO 3040:2012/oprA1:2012
EN ISO 3040:2012/prA1:2012 (E)
Contents Page
Foreword .3
2

---------------------- Page: 4 ----------------------

SIST EN ISO 3040:2012/oprA1:2012
EN ISO 3040:2012/prA1:2012 (E)
Foreword
This document (EN ISO 3040:2012/prA1:2012) has been prepared by Technical Committee ISO/TC 213
"Dimensional and geometrical product specifications and verification" in collaboration with Technical
Committee CEN/TC 290 “Dimensional and geometrical product specification and verification” the secretariat of
which is held by AFNOR.
This document is currently submitted to the parallel Enquiry.
Endorsement notice
The text of ISO 3040:2009/DAM 1:2012 has been approved by CEN as a EN ISO 3040:2012/prA1:2012
without any modification.
3

---------------------- Page: 5 ----------------------

SIST EN ISO 3040:2012/oprA1:2012

---------------------- Page: 6 ----------------------

SIST EN ISO 3040:2012/oprA1:2012

DRAFT AMENDMENT ISO 3040:2009/DAM 1
ISO/TC 213 Secretariat: DS
Voting begins on Voting terminates on

2012-08-09 2013-01-09
INTERNATIONAL ORGANIZATION FOR STANDARDIZATION    МЕЖДУНАРОДНАЯ ОРГАНИЗАЦИЯ ПО СТАНДАРТИЗАЦИИ    ORGANISATION INTERNATIONALE DE NORMALISATION


Geometrical product specifications (GPS) — Dimensioning and
tolerancing — Cones
AMENDMENT 1
Spécification géo
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27