|
oSIST prEN 1317-7:2012
01-september-2012
2SUHPDFHVWGHO5D]UHGLXSRUDEQRVWLPHULOD]DSUHVNXãDQMHREQDOHWXLQ
SUHVNXVQHPHWRGH]D]DNOMXþQLFHLQHOHPHQWHYDUQRVWQLKRJUDM
Road restraint systems - Part 7: Performance classes, impact test acceptance criteria
and test methods for terminals of safety barriers
Rückhaltesysteme an Straßen - Teil 7:Leistungsklassen, Abnahmekriterien für
Anprallprüfungen und Prüfverfahren für Anfangs- und Endkonstruktionen für
Schutzeinrichtungen
Dispositifs de retenue routiers - Partie 7 : Classes de performance, critères d’acceptation
des essais de choc et méthodes d’essai pour les extrémités des barrières de sécurité
Ta slovenski standard je istoveten z: prEN 1317-7
ICS:
13.200 3UHSUHþHYDQMHQHVUHþLQ Accident and disaster control
NDWDVWURI
93.080.30 Cestna oprema in pomožne Road equipment and
naprave installations
oSIST prEN 1317-7:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 1317-7:2012
---------------------- Page: 2 ----------------------
oSIST prEN 1317-7:2012
EUROPEAN STANDARD
DRAFT
prEN 1317-7
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2012
ICS 93.080.30 Will supersede ENV 1317-4:2001
English Version
Road restraint systems - Part 7: Performance classes, impact
test acceptance criteria and test methods for terminals of safety
barriers
Dispositifs de retenue routiers - Partie 7 : Classes de Rückhaltesysteme an Straßen - Teil 7:Leistungsklassen,
performance, critères d'acceptation des essais de choc et Abnahmekriterien für Anprallprüfungen und Prüfverfahren
méthodes d'essai pour les extrémités des barrières de für Anfangs- und Endkonstruktionen für
sécurité Schutzeinrichtungen
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 226.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 1317-7:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 1317-7:2012
prEN 1317-7:2012 (E)
Contents Page
Foreword .3
Introduction .4
1 Scope .5
2 Normative references .5
3 Abbreviations .5
4 Terms and definitions .6
5 Terminal performance . 10
5.1 Performance classes . 10
5.2 Tests for families of terminals .
...