|
SIST EN ISO 10140-3:2010/oprA2:2013
01-november-2013
$NXVWLND/DERUDWRULMVNRPHUMHQMH]YRþQHL]ROLUQRVWLJUDGEHQLKHOHPHQWRYGHO
0HUMHQMHL]ROLUQRVWLSUHGXGDUQLP]YRNRP'RSROQLOR$ ,62 '$0
Acoustics - Laboratory measurement of sound insulation of building elements - Part 3:
Measurement of impact sound insulation - Amendment 2 (ISO 10140-3:2010/DAM
2:2013)
Akustik - Messung der Schalldämmung von Bauteilen im Prüfstand - Teil 3: Messung der
Trittschalldämmung - Änderung 2 (ISO 10140-3:2010/DAM 2:2013)
Acoustique - Mesurage en laboratoire de l'isolation acoustique des éléments de
construction - Partie 3: Mesurage de l'isolation au bruit de choc - Amendement 2 (ISO
10140-3:2010/DAM 2:2013)
Ta slovenski standard je istoveten z: EN ISO 10140-3:2010/prA2
ICS:
17.140.01 $NXVWLþQDPHUMHQMDLQ Acoustic measurements and
EODåHQMHKUXSDQDVSORãQR noise abatement in general
91.120.20 $NXVWLNDYVWDYEDK=YRþQD Acoustics in building. Sound
L]RODFLMD insulation
SIST EN ISO 10140-3:2010/oprA2:2013 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN ISO 10140-3:2010/oprA2:2013
---------------------- Page: 2 ----------------------
SIST EN ISO 10140-3:2010/oprA2:2013
DRAFT AMENDMENT
ISO 10140-3:2010/DAM 2
ISO/TC 43/SC 2 Secretariat: DIN
Voting begins on: Voting terminates on:
2013-09-05 2014-02-05
Acoustics — Laboratory measurement of sound insulation
of building elements —
Part 3:
Measurement of impact sound insulation
AMENDMENT 2
Acoustique — Mesurage en laboratoire de l’isolation acoustique des éléments de construction —
Partie 3: Mesurage de l’isolation au bruit de choc
AMENDEMENT 2
ICS: 91.120.20
ISO/CEN PARALLEL PROCESSING
This draft has been developed within the International Organization for
Standardization (ISO), and processed under the ISO lead mode of collaboration
as defined in the Vienna Agreement.
This draft is hereby submitted to the ISO member bodies and to the CEN member
bodies for a parallel five month enquiry.
Should this draft be accepted, a final draft, established on the basis of comments
received, will be submitted to a parallel two-month approval vote in ISO and
THIS DOCUMENT IS A DRAFT CIRCULATED
formal vote in CEN.
FOR COMMENT AND APPROVAL. IT IS
THEREFORE SUBJECT TO CHANGE AND MAY
NOT BE REFERRED TO AS AN INTERNATIONAL
STANDARD UNTIL PUBLISHED AS SUCH.
To expedite distribution, this document is circulated as received from the
IN ADDITION TO THEIR EVALUATION AS
committee secretariat. ISO Central Secretariat work of editing and text
BEING ACCEPTABLE FOR INDUSTRIAL,
composition will be undertaken at publication stage.
TECHNOLOGICAL, COMMERCIAL AND
USER PURPOSES, DRAFT INTERNATIONAL
STANDARDS MAY ON OCCASION HAVE TO
BE CONSIDERED IN THE LIGHT OF THEIR
POTENTIAL TO BECOME STANDARDS TO
WHICH REFERENCE MAY BE MADE IN
Reference number
NATIONAL REGULATIONS.
ISO 10140-3:2010(E)/DAM 2
RECIPIENTS OF THIS DRAFT ARE INVITED
TO SUBMIT, WITH THEIR COMMENTS,
NOTIFICATION OF ANY RELEVANT PATENT
RIGHTS OF WHICH THEY ARE AWARE AND TO
©
PROVIDE SUPPORTING DOCUMENTATION. ISO 2013
---------------------- Page: 3 ----------------------
SIST EN ISO 10140-3:2010/oprA2:2013
ISO 10140-3:2010(E)/DAM 2
Copyright notice
This ISO document is a Draft International Standard and is copyright-protected by ISO. Except as
permitted under the applicable laws of the user’s country, neither this ISO draft nor any extract
from it may be reproduced, stored in a retrieval system or transmitted in any form or by any means,
electronic, photocopying, recording or otherwise, without prior written permission being secured.
Requests for permission to reproduce should be addressed to either ISO at the address below or ISO’s
member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [email protected]
Web www.iso.org
Reproduction may be subject to royalty payments or a licensing agreement.
Violators may be prosecuted.
ii © ISO 2013 – All rights reserved
---------------------- Page: 4 ----------------------
SIST EN ISO 10140-3:2010/oprA2:2013
ISO 10140-3:2010/DAM 2
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies
(ISO member bodies). The work of preparing International Standards is normally carried out through ISO
technical committees. Each member body interested in a subject for which a technical committee has been
established has the right to be represented on that committee. International organizations, governmental and
non-governmental, in liaison with ISO, also take part in the work. ISO collaborates closely with the
International Electrotechnical Commission (IEC) on all matters of electrotechnical standardization.
International Standards a
...