|
oSIST prEN 12106:2014
01-julij-2014
Cevni sistemi iz polimernih materialov - Cevi iz polietilena (PE) in zamreženega
polietilena (PE-X) - Metoda za preskus odpornosti proti notranjemu tlaku po
izvedenem stiskanju cevi (squeeze-of)
Plastics piping systems - Polyethylene (PE) and crosslinked polyethylene (PE-X) pipes -
Test method for the resistance to internal pressure after application of squeeze-of
Kunststoff-Rohrleitungssysteme - Rohre aus Polyethylen (PE) und vernetztem
Polyethylen (PE-X) - Bestimmung der Widerstandsfähigkeit gegen Innendruck nach
Abquetschen
Systèmes de canalisations en plastique - Tubes en polyéthylène (PE) et polyéthylène
réticulé (PE-X) - Méthode d'essai de résistance à la pression interne après application de
l'écrasement
Ta slovenski standard je istoveten z: prEN 12106
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
oSIST prEN 12106:2014 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 12106:2014
---------------------- Page: 2 ----------------------
oSIST prEN 12106:2014
EUROPEAN STANDARD
DRAFT
prEN 12106
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2014
ICS 23.040.20 Will supersede EN 12106:1997
English Version
Plastics piping systems - Polyethylene (PE) and crosslinked
polyethylene (PE-X) pipes - Test method for the resistance to
internal pressure after application of squeeze-of
Systèmes de canalisations en plastique - Tubes en Kunststoff-Rohrleitungssysteme - Rohre aus Polyethylen
polyéthylène (PE) et polyéthylène réticulé (PE-X) - Méthode (PE) und vernetztem Polyethylen (PE-X) - Bestimmung der
d'essai de résistance à la pression interne après application Widerstandsfähigkeit gegen Innendruck nach Abquetschen
de l'écrasement
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 155.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 12106:2014 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 12106:2014
prEN 12106:2014 (E)
Contents
Page
Foreword .3
1 Scope .4
2 Normative reference .4
3 Principle .4
4 Apparatus .4
5 Test pieces .5
5.1 Preparation .5
5.2 Number .
...