|
oSIST prEN 15013:2014
01-julij-2014
Cevni sistemi iz polimernih materialov - Podzemne cevne komponente za
odvodnjavanje in kanalizacijo, ki delujejo po težnostnem principu - Zahteve in
preskusi/metode ocenjevanja za cevi in fitinge
Plastics piping systems - Non-pressure drainage and sewerage piping components
buried in ground - Requirements and test/assessment methods for pipes and fittings
Kunststoff-Rohrleitungssysteme - Rohrleitungsteile für drucklose erdverlegte
Abwasserkanäle und -leitungen - Anforderungen und Prüf-/Bewertungsverfahren für
Rohre und Formstücke
Systèmes de canalisations en plastique - Composant de canalisation enterrés pour
assainissement sans pression — Exigences et méthodes d’essais/d’évaluation pour
tubes et raccords
Ta slovenski standard je istoveten z: prEN 15013
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
23.040.45 Fitingi iz polimernih Plastics fittings
materialov
93.030 Zunanji sistemi za odpadno External sewage systems
vodo
oSIST prEN 15013:2014 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
oSIST prEN 15013:2014
---------------------- Page: 2 ----------------------
oSIST prEN 15013:2014
EUROPEAN STANDARD
DRAFT
prEN 15013
NORME EUROPÉENNE
EUROPÄISCHE NORM
April 2014
ICS 93.030
English Version
Plastics piping systems - Non-pressure drainage and sewerage
piping components buried in ground - Requirements and
test/assessment methods for pipes and fittings
Systèmes de canalisations en plastique - Composant de Kunststoff-Rohrleitungssysteme - Rohrleitungsteile für
canalisation enterrés pour assainissement sans pression - drucklose erdverlegte Abwasserkanäle und -leitungen -
Exigences et méthodes d'essais/d'évaluation pour tubes et Anforderungen und Prüf-/Bewertungsverfahren für Rohre
raccords und Formstücke
This draft European Standard is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 155.
If this draft becomes a European Standard, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which
stipulate the conditions for giving this European Standard the status of a national standard without any alteration.
This draft European Standard was established by CEN in three official versions (English, French, German). A version in any other language
made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC Management
Centre has the same status as the official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, Former Yugoslav Republic of Macedonia, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania,
Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United
Kingdom.
Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are aware and to
provide supporting documentation.
Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without notice and
shall not be referred to as a European Standard.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
CEN-CENELEC Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2014 CEN All rights of exploitation in any form and by any means reserved Ref. No. prEN 15013:2014 E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
oSIST prEN 15013:2014
prEN 15013:2014 (E)
Contents Page
Foreword .4
Introduction .5
1 Scope .6
2 Normative references .6
3 Terms, definitions and abbreviations .7
3.1 Terms and definitions .7
3.2 Abbreviations .8
4 Requirements .8
4.1 Reaction to fire of pipes and fittings .8
4.2 Maximum load for admissible deformation of pipes and fittings .8
4.2.1 General .8
4.2.2 Ring stiffness of pipes .8
4.2.3 Ring stiffness of fittings .9
4.3 Dimensional tolerances of pipes and fittings .9
4.4 Tightness: Gas and liquid . 10
4.4.1 General . 10
4.4.2 Tightness of sealing ring connections of thermoplastics piping systems . 10
4.4.3 Tightness of connections made by using adhesive bonding or fusion techniques . 10
4.4.4 Tightness of connections of glass-reinforced thermosetting piping systems . 10
4.5 Release of dangerous substances of pipes and fittings . 10
4.6 Durability of pipes and fittings . 11
4.6.1 Durability of pipes and fittings related to maximum load for deformation. 11
4.6.2 Durability of tightness of pipes and fittings . 11
4.6.3 Durability of tightness after temperature cycling test of thermoplastics pipes and fittings
for area D . 11
5 Testing, assessment and sampling methods . 11
5.1 Reaction to fire . 11
5.2 Maximum load for admissible deformation . 12
5.2.1 Ring stiffness of thermoplastics pipes. 12
5.2.2 Ring stiffness of thermoplastics fittings . 12
5.2.3 Ring stiffness of glass-reinforced thermosetting pipes and fittings . 12
5.3 Dimensional tolerances of pipes and fittings . 12
5.4 Tightness: Gas and liquid . 13
5.4.1 Pipes and fittings . 13
5.4.2 Leak-tightness of sealing ring connections of thermoplastics piping systems . 13
5.4.3 Tightness of glass-reinforced thermosetting connections . 13
5.5 Release of dangerous substances . 13
5.6 Durability . 14
5.6.1 Durability of pipes and fittings related to maximum load for deformation. 14
5.6.2 Durability of tightness of pipes and fittings . 14
5.6.3 Durability of tightness after temperature cycling test of thermoplastics pipes and fittings
for area D . 14
6 Evaluation of conformity . 14
6.1 General . 14
6.2 Type Testing . 14
6.2.1 General . 14
6.2.2 Test samples, testing and compliance criteria . 16
6.2.3 Test reports . 18
6.3 Factory production control (FPC) . 18
6.3.1 General . 18
2
---------------------- Page: 4 ----------------------
oSIST prEN 15013:2014
prEN 15013:2014 (E)
6.3.2 Requirements . 19
6.3.3 Product specific requirements . 25
6.3.4 Initial inspection of factory and of FPC (only for reaction to fire under AVCP system 1) . 25
6.3.5 Continuous surveillance of FPC (only for reaction to fire under AVCP system 1) . 26
6.3.6 Procedure for modifications. 26
6.3.7 One-off products and products produced in very low quantity . 26
Annex ZA (informative) Clauses of this European Standard addressing the provisions of EU
Construction Products Regulation . 28
ZA.1 Scope and relevant characteristics . 28
ZA.2 Procedure for AVCP of plastics pipes and fittings . 29
ZA.2.1 System(s) of AVCP . 29
ZA.2.2 Declaration of performance (DoP) . 32
ZA.3 CE marking and labelling. 35
Bibliography . 40
3
---------------------- Page: 5 ----------------------
oSIST prEN 15013:2014
prEN 15013:2014 (E)
Foreword
This document (prEN 15013:2014) has been prepared by Technical Committee CEN/TC 155 “Plastics piping
systems and ducting systems”, the secretariat of which is held by NEN.
This document is currently submitted to the CEN Enquiry.
This document has been prepared under a mandate given to CEN by the European Commission and the
European Free Trade Association, and supports essential requirements of EU Directive(s).
For relationship with EU Directive(s), see informative Annex ZA, which is an integral part of this document.
4
---------------------- Page: 6 ----------------------
oSIST prEN 15013:2014
prEN 15013:2014 (E)
Introduction
This European Standard specifies only those characteristics of pipes and fittings for non-pressure
underground applications for drainage and sewerage that need to be known to determine if the works in which
these are to be installed can satisfy the essential requirements of the EU Directive(s). Additional
characteristics are specified in the documents listed in clause 2 or in other appropriate product specifications.
Chambers and manholes for non-pressure underground sewers are covered by EN 15229 [1] and
EN 15383 [2] under mandate M/118.
5
---------------------- Page: 7 ----------------------
oSIST prEN 15013:2014
prEN 15013:2014 (E)
1 Scope
This European Standard specifies product characteristics for thermoplastics and glass-reinforced
thermosetting pipes and fittings for underground drainage and sewerage applications.
Pipes and fittings covered by this standard are intended to be used for conveyance of drainage and sewerage
water without pressure:
underground in the U area (more than 1 m from the building structure)
underground in the D area (connected to the soil and waste discharge system and buried within or under
the building structure).
This standard gives the associated test/assessment methods.
This standard does not cover adhesives, joint sealings and gaskets.
This standard does not apply to perforated engineering drainage pipes nor to highway drainage pipes,
perforated or non-perforated.
2 Normative references
The following documents, in whole or in part, are normatively referenced in this document and are
indispensable for its application. For dated references, only the edition cited applies. For undated references,
the latest edition of the referenced document (including any amendments) applies.
EN 681-1, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 1: Vulcanized rubber
EN 681-2, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 2: Thermoplastic elastomers
EN 681-3, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 3: Cellular materials of vulcanised rubber
EN 681-4, Elastomeric seals — Materials requirements for pipe joint seals used in water and drainage
applications — Part 4: Cast polyurethane sealing elements
EN 1055, Plastics piping systems — Thermoplastics piping systems for soil and waste discharge inside
buildings — Test method for resistance to elevated temperature cycling
EN 1277:2003, Plastics piping systems — Thermoplastics piping systems for buried non-pressure
applications — Test methods for leaktightness of elastomeric sealing ring type joints
EN 1401-1:2009, Plastics piping systems for non-pressure underground drainage and sewerage —
Unplasticized poly(vinyl chloride) (PVC-U) — Part 1: Specifications for pipes, fittings and the system
EN 1852-1:2009, Plastics piping systems for non-pressure underground drainage and sewerage —
Polypropylene (PP) — Part 1: Specifications for pipes, fittings and the system
EN 12666-1:2005+A1:2011, Plastics piping systems for non-pressure underground drainage and sewerage
— Polyethylene (PE) — Part 1: Specifications for pipes, fittings and the system
EN 13476-2:2007, Plastics piping systems for non-pressure underground drainage and sewerage —
Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and
polyethylene (PE) — Part 2: Specifications for pipes and fittings with smooth internal and external surface and
the system, Type A
6
---------------------- Page: 8 ----------------------
oSIST prEN 15013:2014
prEN 15013:2014 (E)
EN 13476-3:2007+A1:2009, Plastics piping systems for non-pressure underground drainage and sewerage
— Structured-wall piping systems of unplasticized poly(vinyl chloride) (PVC-U), polypropylene (PP) and
polyethylene (PE) — Part 3: Specifications for pipes and fittings with smooth internal and profiled external
surface and the system, Type B
EN 13501-1, Fire classification of construction products and building elements — Part 1: Classification using
test data from reaction to fire tests
EN 13823, Reaction to fire tests for building products — Building products excluding floorings exposed to the
thermal attack by a single burning item
EN 14364:2013, Plastics piping systems for drainage and sewerage with or without pressure — Glass-
reinforced thermosetting plastics (GRP) based on unsaturated polyester resin (UP) — Specifications for pipes,
fittings and joints
EN 14758-1:2012, Plastics piping systems for non-pressure underground drainage and sewerage —
Polypropylene with mineral modifiers (PP-MD) — Part 1: Specifications for pipes, fittings and the system
EN 16000, Plastics piping systems — Systems within the building structure — Mounting and fixing of
components in the test apparatus to thermal attack by a single burning item
EN ISO 3126, Plastics piping systems — Plastics components — Determination of dimensions
(ISO 3126:2005)
EN ISO 9967, Plastics pipes Determination of creep ratio (ISO 9967:1994)
EN ISO 9969, Thermoplastics pipes — Determination of ring stiffness (ISO 9969:2007)
EN ISO 13967, Thermoplastics fittings — Determination of ring stiffness
EN ISO 13968, Plastics piping and ducting systems - Thermoplastics pipes - Determination of ring flexibility
(ISO 13968:2008)
ISO 13966, Thermoplastics pipes and fittings — Nominal ring stiffnesses
3 Terms, definitions and abbreviations
3.1 Terms and definitions
For the purposes of this document, the following terms and definitions apply.
3.1.1
nominal size
DN
numerical designation of the size of a component, other than a component designated by thread size, which is
a convenient round number approximately equal to the manufacturing dimension
Note 1 to entry: This can apply to either the internal diameter (DN/ID) or external diameter (DN/OD).
Note 2 to entry: The nominal size is expressed in millimetres (mm).
3.1.2
nominal outside diameter
d
n
specified diameter, in millimetres, assigned to a nominal size (for thermoplastics pipes and fittings only)
7
---------------------- Page: 9 ----------------------
oSIST prEN 15013:2014
prEN 15013:2014 (E)
3.1.3
nominal ring stiffness
SN
numerical designation of the ring stiffness of a pipe or fitting, which is a convenient round number indicating
the minimum required ring stiffness of the pipe or fitting
Note 1 to entry: It is designated by the letters "SN" followed by the appropriate number.
3.1.4
connection
assembly of pipe or fitting to another pipe(s) or fitting
NOTE 1 to entry: For this standard, the term fitting includes also the term joint.
3.2 Abbreviations
For the purposes of this document, the following abbreviations apply.
GRP: glass-reinforced thermosetting plastics
GRP UP: glass-reinforced thermosetting plastics based on unsaturated polyester resin
PE: polyethylene
PP: polypropylene
PP-MD: polypropylene with mineral modifiers
PVC-U: unplasticized poly(vinyl chloride)
SN: nominal ring stiffness
CWFT: classified without further testing
FPC: factory production control
NPD: no performance determined
4 Requirements
4.1 Reaction to fire of pipes and fittings
The contribution to fire development of products falling under the scope of this European standard is verified
according to the provisions of 5.1.
Test results shall be expressed by classification.
4.2 Maximum load for admissible deformation of pipes and fittings
4.2.1 General
Pipes and fittings must have the ability to withstand the loads created by the surrounding soil as well as loads
created by traffic above the installation.
NOTE The maximum load for admissible deformation is addressed as ring stiffness.
4.2.2 Ring stiffness of pipes
4.2.2.1 Thermoplastics pipes
The ring stiffness of a thermoplastics pipe shall be determined in accordance with 5.2.1 and shall be
expressed either:
a) as SN 2, SN 4, SN 8 or SN 16 in accordance with ISO 13966, or
8
---------------------- Page: 10 ----------------------
oSIST prEN 15013:2014
prEN 15013:2014 (E)
b) for dimensions DN ≥ 600 as the declared minimum value based on the test, expressed in kN/m2.
4.2.2.2 Glass-reinforced thermosetting pipes
The ring stiffness of a glass-reinforced thermosetting pipe shall be determined in accordance with 5.2.2. The
SN and shall be declared either:
a) as SN 1250, SN 2500, SN 5000 or SN 10000, or
2
b) as an SN value based on the test, expressed in N/m .
4.2.3 Ring stiffness of fittings
4.2.3.1 General
The manufacturer shall declare the ring stiffness of the fitting in accordance with 4.2.3.2 or 4.2.3.3, as
applicable.
4.2.3.2 Thermoplastics fittings
The ring stiffness of the body of thermoplastics fittings shall be expressed either:
a) as SN 2, SN 4, SN 8 or SN 16 in accordance with ISO 13966, or
2
b) as the actual value obtained, expressed in kN/m . The ring stiffness of a fitting made from the same
material and having the same wall thickness and design as the corresponding pipe may, because of
the geometry, be declared to have the same stiffness as that of the associated pipe.
For thermoplastics fittings with structured wall the ring stiffness of bends and branches with the largest side
branch shall be determined in accordance with 5.2.3. Based on the obtained lowest value of the result other
fittings of the same design family shall be classified with the same stiffness class.
4.2.3.3 Glass-reinforced thermosetting fittings
The ring stiffness of glass-reinforced thermosetting fittings shall be expressed either:
a) as the nominal ring stiffness of the pipe for which the fitting is designed, in accordance with 4.2.2.2
a), or
b) as the actual value of the nominal ring stiffness SN used for the design of the fitting, where the
manufacturer shall be able to show conformity with this value.
The ring stiffness of a fitting made from the same material and having the same wall thickness and design as
the corresponding pipe may, because of the geometry, be declared to have the same stiffness as that of the
associated pipe.
4.3 Dimensional tolerances of pipes and fittings
Dimensions including the dimensional tolerances are assuring the proper functioning of the connections when
installing the pipes and fittings:
a) Dimensions shall be measured in accordance with 5.3. The dimensions and the dimensional tolerances
shall comply with what is declared by the manufacturer. This shall be done by using the values given in
one of the documents listed hereafter: a specific European standard as given in Clause 2, as applicable,
b) only in the absence of a), a specific publicly available product specification,
c) only in the absence of a) and b), an International Standard,
9
---------------------- Page: 11 ----------------------
oSIST prEN 15013:2014
prEN 15013:2014 (E)
d) only in the absence of a), b), and c), by stating the values of his own specification and associated
connecting method.
For thermoplastics pipes and fittings, the test results shall be expressed as a DN/OD or DN/ID value, as
applicable and nominal wall thickness, if applicable.
For thermosetting pipes and fittings, the test result shall be expressed as a DN value with the appropriate
diameter series.
4.4 Tightness: Gas and liquid
4.4.1 General
Pipes, fittings and their connections shall be tight.
4.4.2 Tightness of sealing ring connections of thermoplastics piping systems
Sealing ring connections between pipes and fittings shall be assembled according to the manufacturer's
instructions and:
a) tightness under deformation shall be tested in accordance with 5.4.1.1.
b) tightness under angular deflection shall be tested in accordance with 5.4.1.2.
In order to enable the declaration of leak-tightness of sealing ring connections, the following applies:
no water leakage may occur;
the loss of partial vacuum shall not exceed 3 kPa (10 %).
4.4.3 Tightness of connections made by using adhesive bonding or fusion techniques
Connection systems using adhesive bonding or fusion techniques are considered to be tight when assembled
in accordance with the manufacturer's instructions. Such instructions shall be made available by the
manufacturer.
4.4.4 Tightness of connections of glass-reinforced thermosetting piping systems
Tightness of connections of glass-reinforced thermosetting piping systems shall be tested in accordance with
5.4.2.
No leakage shall occur during the test period.
4.5 Release of dangerous substances of pipes and fittings
National regulations on dangerous substances may require verification and declaration on release, and
sometimes content, when construction products covered by this standard are placed on those markets. In the
absence of European harmonized test methods, verification and declaration on release/content should be
done taking into account national provisions in the place of use.
NOTE An informative database covering European and national provisions on dangerous substances is available at
the Construction web site on EUROPA accessed through: http://ec.europa.eu/enterprise/construction/cpd-ds/.
10
---------------------- Page: 12 ----------------------
oSIST prEN 15013:2014
prEN 15013:2014 (E)
4.6 Durability of pipes and fittings
4.6.1 Durability of pipes and fittings related to maximum load for deformation
4.6.1.1 Durability of thermoplastics pipes and fittings
The durability of the ability to withstand maximum load for deformation shall be assessed by testing in
accordance with 5.6.1.1 with the conditions and requirements as given in the relevant standard referenced in
clause 2, as applicable.
• no decrease of the measured force during the test;
• no cracking in any part of the wall structure except in ends of cut structures;
• no wall delamination or other type of ruptures except possible delamination in ends of cut structures;
• no permanent buckling in any part of the structure of the pipe wall.
• a creep ratio not exceeding 4,0.
The requirement shall be met.
4.6.1.2 Durability of glass-reinforced thermosetting pipes and fittings
The durability of the ability of glass-reinforced pipes and fittings to withstand maximum load for deformation
shall be assessed by testing in accordance with 5.6.1.2 with the conditions and requirements as given in the
relevant clauses in EN 14364, as applicable.
The requirement shall be met.
4.6.2 Durability of tightness of pipes and fittings
The durability of tightness of elastomeric sealing connections shall be assessed by control of the seal material
quality in accordance with 5.6.2
4.6.3 Durability of tightness after temperature cycling test of thermoplastics pipes and fittings for
area D
The durability of tightness after temperature cycling of thermoplastics pipes and fittings used for D area shall
be tested in accordance with 5.6.3.
The connections between pipes and/or fittings shall not show any leakage before and after the test.
5 Testing, assessment and sampling methods
5.1 Reaction to fire
The reaction to fire is tested according to the test method relevant for the claimed class.
When tested in accordance with EN 13823 (SBI test), the mounting and fixing conditions of the samples to be
tested shall be in accordance with EN 16000.
Test results shall be classified according to EN 13501-1.
11
---------------------- Page: 13 ----------------------
oSIST prEN 15013:2014
prEN 15013:2014 (E)
5.2 Maximum load for admissible deformation
5.2.1 Ring stiffness of thermoplastics pipes
For thermoplastics pipes the ring stiffness shall be determined by testing in accordance with EN ISO 9969.
The test result shall meet to the declared SN value in accordance with ISO 13966 or the specific ring stiffness
value declared for the tested product.
5.2.2 Ring stiffness of thermoplastics fittings
For thermoplastics fittings with structured wall the ring stiffness of bends and branches shall be determined by
testing in accordance with EN ISO 13967.
The test
...