EN 14492-2:2019/prA1

Cranes - Power driven winches and hoists - Part 2: Power driven hoists

EN 14492-2:2019/prA1

Name:EN 14492-2:2019/prA1   Standard name:Cranes - Power driven winches and hoists - Part 2: Power driven hoists
Standard number:EN 14492-2:2019/prA1   language:English language
Release Date:04-Jul-2024   technical committee:CEN/TC 147 - Cranes - Safety
Drafting committee:CEN/TC 147/WG 17 - Power driven winches and hoists   ICS number:53.020.20 - Cranes
SLOVENSKI STANDARD
SIST EN 14492-2:2019/oprA1:2022
01-september-2022
Žerjavi - Motorni vitli in dvižni mehanizmi - 2. del: Motorni dvižni mehanizmi -
Dopolnilo A1
Cranes - Power driven winches and hoists - Part 2: Power driven hoists
Krane - Kraftgetriebene Winden und Hubwerke - Teil 2: Kraftgetriebene Hubwerke
Appareils de levage à charge suspendue - Treuils et palans motorises - Partie 2 : Palans
et treuils de levage motorisés
Ta slovenski standard je istoveten z: EN 14492-2:2019/prA1
ICS:
53.020.20 Dvigala Cranes
SIST EN 14492-2:2019/oprA1:2022 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------
SIST EN 14492-2:2019/oprA1:2022

---------------------- Page: 2 ----------------------
SIST EN 14492-2:2019/oprA1:2022


DRAFT
EUROPEAN STANDARD
EN 14492-2:2019
NORME EUROPÉENNE

EUROPÄISCHE NORM
prA1
July 2022
ICS 53.020.20
English Version

Cranes - Power driven winches and hoists - Part 2: Power
driven hoists
Appareils de levage à charge suspendue - Treuils et Krane - Kraftgetriebene Winden und Hubwerke - Teil
palans motorises - Partie 2 : Palans et treuils de levage 2: Kraftgetriebene Hubwerke
motorisés
This draft amendment is submitted to CEN members for enquiry. It has been drawn up by the Technical Committee CEN/TC 147.

This draft amendment A1, if approved, will modify the European Standard EN 14492-2:2019. If this draft becomes an
amendment, CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for
inclusion of this amendment into the relevant national standard without any alteration.

This draft amendment was established by CEN in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CEN member into its own language and notified to the CEN-CENELEC
Management Centre has the same status as the official versions.

CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway,
Poland, Portugal, Republic of North Macedonia, Romania, Serbia, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and
United Kingdom.

Recipients of this draft are invited to submit, with their comments, notification of any relevant patent rights of which they are
aware and to provide supporting documentation.

Warning : This document is not a European Standard. It is distributed for review and comments. It is subject to change without
notice and shall not be referred to as a European Standard.


EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION

EUROPÄISCHES KOMITEE FÜR NORMUNG

CEN-CENELEC Management Centre: Rue de la Science 23, B-1040 Brussels
© 2022 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 14492-2:2019/prA1:2022 E
worldwide for CEN national Members.

---------------------- Page: 3 ----------------------
SIST EN 14492-2:2019/oprA1:2022
prEN 14492-2:2019/prA1:2022 (E)
Contents Page
European foreword . 3
1 Modifications to the European foreword . 4
2 Modifications to the Introduction . 4
3 Modifications to Clause 1, "Scope" . 4
4 Modifications to Clause 2, "Normative references" . 5
5 Modifications to Clause 3, "Terms, definitions and symbols " . 7
6 Modifications to Clause 4, "List of significant hazards " . 8
7 Modifications to Clause 5, " Safety requirements and/or protective measures " . 8
8 Modifications to Clause 6, "Verification of the safety requirements and/or protective
measures" . 14
9 Modifications to Clause 7, "User information" . 15
10 Modifications to Annex B, "Classification" . 15
11 Modifications to Annex C, "Guidance on hoist classification" .
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27