1. Installation height of floor heating water collector
The installation of floor heating water collector actually needs to be divided into two parts: one is the installation of the floor heating water collector and the other is the installation. floor heating water collector. The installation heights of these two different components are inconsistent.
1. The installation height of the floor heating water dispenser
The floor heating water dispenser refers to the water distribution rod connected to our outdoor water supply pipe . This water dispenser allows you to divide the incoming water into different circuits and then provide heat to the room. Therefore, its installation position is generally high on the upper side.
Height requirements: At present, the most common installation height of floor heating water dispenseris generally 600mm from the finished floor surface. That's to say. When we determine the height of the underfloor heating water dispenser, simply measure up to 600mm from the floor based on the center line of the water dispenser pipe.
2. The installation height of the floor heating water collector
The floor heating water collector is connected to the main indoor water return pipe. Its function is to collect water after internal water. the supply has been distributed. It then passes through the main water return pipe and returns to the outdoor heating pipe network. Therefore, the main water return pipe is usually installed on the lower side of the water dispenser, which is higher than the main water supply pipe.
Height Requirements: The common installation height requirement for the water collector main pipe is enapproximately 400mm from the finished floor surface. The specific measurement method is to measure a height of 400mm from the ground and stretch the line on the wall. This line is the center line of the main water collection pipe.
2. Method of adjusting the underfloor heating sub-manifold
1. Slow switch for the first time
When the installed floor heating is started for the first time. , it is necessary to open the underfloor heating sub-manifold. The water supply valve to the water heater. Horizontal state means open and vertical state means closed. At this time, you should pay attention to the slow opening speed. If you open it directly, the water collector will leak and hot water will spurt out directly, which is dangerous.
2. Debugging the exhaust for the first time
As with the radiator, there will be a lot of air in the installed floor heating pipes. Heating pipesby the ground are long and circuitous. , which can easily cause air blockage and the circulation of floor heating is not good. It is difficult to achieve normal heat dissipation if it is unblocked. It is essential to debug the escape in time. Close all valves before draining and drain them one by one.
3. Cleaning work
The inside of the underfloor heating water collector has a component that blocks impurities - a filter. Impurities present in the construction of heating water and underfloor heating can accumulate in the water collector filter, so this must be removed and cleaned regularly. Before cleaning, close all valves, use a wrench to open the filter counterclockwise, remove the inner mesh and rinse.
4. Flexible temperature adjustment
Adjust the temperature via the coll water supply valvewater source for underfloor heating. Specifically, set the water supply valve to maximum and the water flow will adjust. improve the heat dissipation in the room, making it faster and warmer, conversely, turning it down will lower the temperature when you go out temporarily or on a business trip. It should be noted that at the beginning of heating, the heating speed of floor heating is slow, and the floor heating speed is basically about 2 days. Never act in a hurry.
If there is no heat, you can evacuate the water and air according to the circuit of the room to clear the pipes.
Where to buy a floor heating water dispenser cover - How to cover a floor heating water dispenser -
There are many types of heating equipment on the market, including underfloor heating and radiators. When choosing Heating equipment can be purchased independing on the needs of each family. If you are considering purchasing underfloor heating, you should pay attention to replacing the feng shui device when using underfloor heating. For example, how many years should geothermal water be used. Does the distributor need to be replaced? How to replace underfloor heating? What issues should we pay attention to? The editor below will present you with relevant content.
1. The floor heating water dispenser needs to be replaced every few years.
The lifespan of most floor heating water dispensers is about 10 years, which means that they need to be replaced every few years. 10 years. However, the specific situation depends on the water quality. If the water quality is relatively poor, it will need to be replaced approximately every 7 years. Additionally, this is also related to the material of the water dispenser. The most popular materialsCommon types of water dispenser are stainless steel, pure copper and plastic. Among them, pure copper has the best corrosion resistance and the longest service life.
2. Under what circumstances should the water dispenser be replaced?
1. It turns out that the water dispenser is leaking and rust spots appear on the surface of the water. distributer.
2. When I used my hands to adjust the rotary valve, I found that the rotary valve was corroded and could not be turned.
3. The underfloor heating in the house has been used for over 10 years.
3. What are the advantages of underfloor heating
1. The heat dissipation is relatively uniform and the heat is emitted from the ground, so the comfort of the human body is relatively good, and this does not exist in our home. The air pollution situation.
2. Compared with some other heating equipment, it is moreenergy efficient and can be adjusted according to the temperature of the house when in use.
3. The stability of heat dissipation is relatively good. Once the floor heating is turned on, the indoor temperature will slowly rise, making people feel more comfortable.
4. It will not occupy too much use area in the house, because the underfloor heating is installed under the floor and there will be no corrosion.
IV. Tips for using the floor heating water dispenser
1. If there is often no one at home, the water volume of the main valve of the water dispenser should be adjusted to the minimum, but do not close them all, otherwise it will lead to problems with the underfloor heating pipes.
2. Install a manual exhaust valve on the water dispenser to prevent air blocking or blockage of floor heating pipes.
Friendss in the North generally have underfloor heating installed in their homes. To think that those who don't know about underfloor heating are probably only people from the South. Actually, floor heating is really a very common thing in the north, because they have to rely on floor heating for winter, but people who know about floor heating also need to know that when When installing underfloor heating, the underfloor heating water dispenser always looks very ugly. Therefore, everyone tries their best to conceal it, so.Where do you usually buy a cover to cover a floor heating water dispenser? Let’s look at it together!
Where to buy a cover for a floor heating water dispenser 1. Brand door-to-door design of floor heating water dispenser cover For covers, some decoration companies or professional installation companiesprofessionals can come and measure the part then design and produce it professionally.
2. Purchase in physical stores. In addition, we can also go to specialized stores to purchase covers for underfloor heating water dispensers. This method of purchasing will be more convenient and the purchased products will be safer after all. , we saw the products in person. If you buy again, you can be sure of the quality of the product.
3. Online Purchase Moreover, the cover of this water dispenser can also be purchased online. After all, we are in the Internet age and many things can be successfully purchased without leaving home. -home delivery, extremely convenient. But the disadvantage of this method is that the quality cannot be guaranteed.
After understanding where to buy the cover for the floor heating water dispenser, let's learn how to cover thee floor heating water dispenser in general!
How to cover the floor heating water distributor in general? It is said that the water distributor of underfloor heating can be blocked with a special protective casing, and this method is also very easy to use and practical. It can not only beautify the environment, but also effectively protect the water dispenser. product. .
1. Advantages of floor heating water distributor protective box. The protective box of the underfloor heating water dispenser is usually a box hidden in the kitchen cabinet. Although there are also exposed enclosures, concealed enclosures cannot. only it saves space and can satisfy the aesthetics of the house.
2. The price of the protective casing of the underfloor heating water distributor. The price of the protective casing of the hot water dispenserunderfloor heating does not have a clear number, since its price depends on the brand, brand of auxiliary materials. , installation cost, material, etc. It matters, the price will be different if the conditions are different, so it should always be based on personal choice.
3. The material of the protective casing of the underfloor heating water distributor. There are still many protective casing materials on the market. Generally, most people will choose aluminum-plastic panels, but if you like the texture, you can. also choose It is made of artificial stone, but this material is very bulky and difficult to transport.
After installing a water dispenser for underfloor heating, everyone usually wants to cover it with something because it doesn't look good. Then you can also try to cover it with a blocking box or cover, so that your house ismore beautiful.