|
SIST ISO 12643-3:2014
01-marec-2014
1DGRPHãþD
SIST ISO 12643-3:2010
*UDILþQDWHKQRORJLMD9DUQRVWQH]DKWHYH]DJUDILþQRWHKQRORãNRRSUHPRLQ
VLVWHPHGHO 2SUHPDYNQMLJRYH]QLFLLQJUDILþQLGRGHODYLWHUVLVWHPL
Graphic technology - Safety requirements for graphic technology equipment and systems
- Part 3: Binding and finishing equipment and systems
Technologie graphique - Exigences de sécurité pour les systèmes et l'équipement de
technologie graphique - Partie 3: Systèmes et équipment de reliure et de finissage
Ta slovenski standard je istoveten z: ISO 12643-3:2010
ICS:
37.100.10 Reprodukcijska oprema Reproduction equipment
SIST ISO 12643-3:2014 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST ISO 12643-3:2014
---------------------- Page: 2 ----------------------
SIST ISO 12643-3:2014
INTERNATIONAL ISO
STANDARD 12643-3
Second edition
2010-12-15
Graphic technology — Safety
requirements for graphic technology
equipment and systems —
Part 3:
Binding and finishing equipment
and systems
Technologie graphique — Exigences de sécurité pour les systèmes
et l'équipement de technologie graphique —
Partie 3: Systèmes et équipement de reliure et de finissage
Reference number
ISO 12643-3:2010(E)
©
ISO 2010
---------------------- Page: 3 ----------------------
SIST ISO 12643-3:2014
ISO 12643-3:2010(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.
COPYRIGHT PROTECTED DOCUMENT
© ISO 2010
or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [email protected]
Web www.iso.org
Published in Switzerland
ii © ISO 2010 – All rights reserved
---------------------- Page: 4 ----------------------
SIST ISO 12643-3:2014
ISO 12643-3:2010(E)
Contents Page
Foreword .iv
Introduction.v
1 Scope.1
2 Normative references.1
3 Terms and definitions .2
4 Conformity with this part of ISO 12643 .5
5 Guarding of significant hazards .5
5.1 General .5
5.2 Interlocks.5
5.3 Guarding of hoppers and hopper feeders .6
5.4 Guarding on binding and finishing machines.6
5.5 Inserting and collating machines .23
5.6 Counter-stackers.
...