|
SIST EN 61073-1:2009
01-julij-2009
1DGRPHãþD
SIST EN 61073-1:2002
3RYH]RYDOQHQDSUDYHLQSDVLYQHNRPSRQHQWHRSWLþQLKYODNHQâþLWQLNLPHKDQVNLK
LQYDUMHQLKVSRMQLKPHVW]DRSWLþQDYODNQDLQNDEOHGHO 5RGRYQDVSHFLILNDFLMD
,(&
Fibre optic interconnecting devices and passive components - Mechanical splices and
fusion splice protectors for optical fibres and cables - Part 1: Generic specification (IEC
61073-1:2009)
Lichtwellenleiter - Verbindungselemente und passive Bauteile - Mechanische Spleiße
und Fusionsspleißschutze für optische Fasern und Kabel - Teil 1: Fachgrundspezifikation
(IEC 61073-1:2009)
Dispositifs d'interconnexion et composants passifs à fibres optiques - Epissures
mécaniques et protecteurs d'épissures par fusion pour fibres et câbles optiques - Partie
1: Spécification générique (CEI 61073-1:2009)
Ta slovenski standard je istoveten z: EN 61073-1:2009
ICS:
33.180.20 3RYH]RYDOQHQDSUDYH]D Fibre optic interconnecting
RSWLþQDYODNQD devices
SIST EN 61073-1:2009 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 61073-1:2009
---------------------- Page: 2 ----------------------
SIST EN 61073-1:2009
EUROPEAN STANDARD
EN 61073-1
NORME EUROPÉENNE
April 2009
EUROPÄISCHE NORM
ICS 33.180.20 Supersedes EN 61073-1:2000
English version
Fibre optic interconnecting devices and passive components -
Mechanical splices and fusion splice protectors
for optical fibres and cables -
Part 1: Generic specification
(IEC 61073-1:2009)
Dispositifs d'interconnexion Lichtwellenleiter -
et composants passifs à fibres optiques - Verbindungselemente
Epissures mécaniques et protecteurs und passive Bauteile -
d'épissures par fusion pour fibres Mechanische Spleiße
et câbles optiques - und Fusionsspleißschutze
Partie 1: Spécification générique für optische Fasern und Kabel -
(CEI 61073-1:2009) Teil 1: Fachgrundspezifikation
(IEC 61073-1:2009)
This European Standard was approved by CENELEC on 2009-02-01. CENELEC members are bound to comply
with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European Standard
the status of a national standard without any alteration.
Up-to-date lists and bibliographical references concerning such national standards may be obtained on
application to the Central Secretariat or to any CENELEC member.
This European Standard exists in three official versions (English, French, German). A version in any other
language made by translation under the responsibility of a CENELEC member into its own language and notified
to the Central Secretariat has the same status as the official versions.
CENELEC members are the national electrotechnical committees of Austria, Belgium, Bulgaria, Cyprus, the
Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia,
Lithuania, Luxembourg, Malta, the Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain,
Sweden, Switzerland and the United Kingdom.
CENELEC
European Committee for Electrotechnical Standardization
Comité Européen de Normalisation Electrotechnique
Europäisches Komitee für Elektrotechnische Normung
Central Secretariat: avenue Marnix 17, B - 1000 Brussels
© 2009 CENELEC - All rights of exploitation in any form and by any means reserved worldwide for CENELEC members.
Ref. No. EN 61073-1:2009 E
---------------------- Page: 3 ----------------------
SIST EN 61073-1:2009
EN 61073-1:2009 - 2 -
Foreword
The text of document 86B/2773/FDIS, future edition 4 of IEC 61073-1, prepared by SC 86B, Fibre optic
interconnecting devices and passive components, of IEC TC 86, Fibre optics, was submitted to the
IEC-CENELEC parallel vote and was approved by CENELEC as EN 61073-1 on 2009-02-01.
This European Standard supersedes EN 61073-1:2000.
The main changes with respect to EN 61073-1:2000 are as follows:
– terms and definitions have been reconsidered;
– style has been added in classification of requirement;
– environmental category has been deleted from classification of requirement;
– standardisation structure and standards interlink have been reconsidered.
The following dates were fixed:
– latest date by which the EN has to be implemented
at national level by publication of an identical
national standard or by endorsement (dop) 2009-11-01
– latest date by which the national standards conflicting
with the EN have to be withdrawn (dow) 2010-02-01
Annex ZA has been added by CENELEC.
__________
Endorsement notice
The text of the International Standard IEC 61073-1:2009 was approved by CENELEC as a European
Standard without any modification.
__________
---------------------- Page: 4 ----------------------
SIST EN 61073-1:2009
- 3 - EN 61073-1:2009
Annex ZA
(normative)
Normative references to international publications
with their corresponding European publications
The following referenced documents are indispensable for the application of this document. For dated
references, only the edition cited applies. For undated references, the latest edition of the referenced
document (including any amendments) applies.
NOTE When an international publication has been modified by common modifications, indicated by (mod), the relevant EN/HD
applies.
Publication Year Title EN/HD Year
IEC 60027 Series Letter symbols to be used in electrical EN 60027 Series
technology
1)
IEC 60050-731 - International Electrotechnical Vocabulary - -
(IEV) -
Chapter 731: Optical fibre communication
IEC 60617 Series Graphical symbols for diagrams - -
1) 2)
IEC 60695-11-5 - Fire hazard testing - EN 60695-11-5 2005
Part 11-5: Test flames - Needle-flame test
method - Apparatus, confirmatory test
arrangement and guidance
IEC 60793-1 Series Optical fibres - EN 60793-1 Series
(mod) Part 1: Measurement methods and test
procedures
1) 2)
IEC 60825-1 - Safety of laser products - EN 60825-1 2007
Part 1: Equipment classification and
requirements
1) 2)
IEC 61300-1 - Fibre optic interconnecting devices and EN 61300-1 2003
passive components - Basic test and
measurement procedures -
Part 1: General and guidance
IEC 61300-2 Series Fibre optic interconnecting devices and EN 61300-2 Series
passive components - Basic test and
measurement procedures -
Part 2: Tests
IEC 61300-3 Series Fibre optic interconnecting devices and EN 61300-3 Series
passive components - Basic test and
measurement procedures -
Part 3: Examinations and measurements
1)
IEC/TR 61930 - Fibre optic graphical symbology - -
1)
IEC/TR 61931 - Fibre optic - Terminology - -
1)
IEC QC 001002-3 - IEC Quality Assessment System for - -
Electronic Components (IECQ) -
Rules of Procedure -
Part 3: Approval procedures
1)
Undated reference.
2)
Valid edition at date of issue.
---------------------- Page: 5 ----------------------
SIST EN 61073-1:2009
EN 61073-1:2009 - 4 -
Publication Year Title EN/HD Year
1)
IEC Guide 102 - Electronic components - Specification - -
structures for quality assessment
(Qualification approval and capability
approval)
1)
ISO 129-1 - Technical drawings - Indication of - -
dimensions and tolerances -
Part 1: General principles
1)
ISO 286-1 - ISO system of limits and fits - - -
Part 1: Bases of tolerances, deviations and fits
1) 2)
ISO 1101 - Geometrical Product Specifications (GPS) - EN ISO 1101 2005
Geometrical tolerancing - Tolerances of form,
orientation, location and run-out
1)
ISO 8601 - Data elements and interchange formats - - -
Information interchange - Representation of
dates and times
---------------------- Page: 6 ----------------------
SIST EN 61073-1:2009
IEC 61073-1
Edition 4.0 2009-01
INTERNATIONAL
STANDARD
Fibre optic interconnecting devices and passive components – Mechanical
splices and fusion splice protectors for optical fibres and cables –
Part 1: Generic specification
INTERNATIONAL
ELECTROTECHNICAL
COMMISSION
PRICE CODE
R
ICS 33.180.20 ISBN 2-8318-1023-0
Registered trademark of the International Electrotechnical Commission
---------------------- Page: 7 ----------------------
SIST EN 61073-1:2009
– 2 – 61073-1 © IEC:2009(E)
CONTENTS
FOREWORD.0H3
1 Scope.1H5
2 Normative references.2H5
3 Terms and definitions .3H6
4 Requirements .4H7
4.1 Classification.5H7
4.1.1 Type .6H8
4.1.2 Arrangement.7H8
4.1.3 Style .8H8
4.1.4 Variant.9H9
4.1.5 Assessment level.10H10
4.1.6 Normative reference extensions .11H10
4.2 Documentation .12H11
4.2.1 Symbols.13H11
4.2.2 Specification system .14H11
4.2.3 Drawings .15H13
4.2.4 Performance.16H13
4.2.5 Measurements .17H13
4.2.6 Test reports .18H13
4.2.7 Instructions for use .19H14
4.3 Standardisation system.20H14
4.3.1 Performance standards.21H14
4.3.2 Reliability standards.22H14
4.3.3 Interlinking.23H15
4.4 Design and construction .24H16
4.4.1 Materials.25H16
4.4.2 Workmanship .26H16
4.5 Performance.27H17
4.6 Identification and marking.28H17
4.6.1 Variant identification number.29H17
4.6.2 Component marking.30H17
4.6.3 Package marking .31H17
4.7 Packaging .32H18
4.8 Storage conditions.33H18
4.9 Safety.34H18
Figure 1 – Standardisation structure .35H16
Table 1 – Example of a typical mechanical splice and fusion splice protection hardware .36H8
Table 2 – Three-level specification structure.37H12
Table 3 – Standards interlink matrix .38H16
---------------------- Page: 8 ----------------------
SIST EN 61073-1:2009
61073-1 © IEC:2009(E) – 3 –
INTERNATIONAL ELECTROTECHNICAL COMMISSION
____________
FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS –
MECHANICAL SPLICES AND FUSION SPLICE PROTECTORS
FOR OPTICAL FIBRES AND CABLES –
Part 1: Generic specification
FOREWORD
1) The International Electrotechnical Commission (IEC) is a worldwide organization for standardization comprising
all national electrotechnical committees (IEC National Committees). The object of IEC is to promote
international co-operation on all questions concerning standardization in the electrical and electronic fields. To
this end and in addition to other activities, IEC publishes International Standards, Technical Specifications,
Technical Reports, Publicly Available Specifications (PAS) and Guides (hereafter referred to as “IEC
Publication(s)”). Their preparation is entrusted to technical committees; any IEC National Committee interested
in the subject dealt with may participate in this preparatory work. International, governmental and non-
governmental organizations liaising with the IEC also participate in this preparation. IEC collaborates closely
with the International Organization for Standardization (ISO) in accordance with conditions determined by
agreement between the two organizations.
2) The formal decisions or agreements of IEC on technical matters express, as nearly as possible, an international
consensus of opinion on the relevant subjects since each technical committee has representation from all
interested IEC National Committees.
3) IEC Publications have the form of recommendations for international use and are accepted by IEC National
Committees in that sense. While all reasonable efforts are made to ensure that the technical content of IEC
Publications is accurate, IEC cannot be held responsible for the way in which they are used or for any
misinterpretation by any end user.
4) In order to promote international uniformity, IEC National Committees undertake to apply IEC Publications
transparently to the maximum extent possible in their national and regional publications. Any divergence
between any IEC Publication and the corresponding national or regional publication shall be clearly indicated in
the latter.
5) IEC provides no marking procedure to indicate its approval and cannot be rendered responsible for any
equipment declared to be in conformity with an IEC Publication.
6) All users should ensure that they have the latest edition of this publication.
7) No liability shall attach to IEC or its directors, employees, servants or agents including individual experts and
members of its technical committees and IEC National Committees for any personal injury, property damage or
other damage of any nature whatsoever, whether direct or indirect, or for costs (including legal fees) and
expenses arising out of the publication, use of, or reliance upon, this IEC Publication or any other IEC
Publications.
8) Attention is drawn to the Normative references cited in this publication. Use of the referenced publications is
indispensable for the correct application of this publication.
9) Attention is drawn to the possibility that some of the elements of this IEC Publication may be the subject of
patent rights. IEC shall not be held responsible for identifying any or all such patent rights.
International Standard IEC 61073-1 has been prepared by subcommittee 86B: Fibre optic
interconnecting devices and passive components, of IEC technical committee 86: Fibre optics.
This fourth edition cancels and replaces the third edition published in 1999. This edition
constitutes a technical revision. The main changes with respect to the previous edition are as
follows:
• terms and definitions have been reconsidered;
• style has been added in classification of requirement;
• environmental category has been deleted from classification of requirement;
• standardisation structure and standards interlink have been reconsidered.
---------------------- Page: 9 ----------------------
SIST EN 61073-1:2009
– 4 – 61073-1 © IEC:2009(E)
The text of this standard is based on the following documents:
FDIS Report on voting
86B/2773/FDIS 86B/2805/RVD
Full information on the voting for the approval of this standard can be found in the report on
voting indicated in the above table.
This publication has been drafted in accordance with the ISO/IEC Directives, Part 2.
The committee has decided that the contents of this publication will remain unchanged until the
maintenance result date indicated on the IEC web site under "http://webstore.iec.ch" in the data
related to the specific publication. At this date, the publication will be
• reconfirmed,
• withdrawn,
• replaced by a revised edition, or
• amended.
A bilingual version of this publication may be issued at a later date.
---------------------- Page: 10 ----------------------
SIST EN 61073-1:2009
61073-1 © IEC:2009(E) – 5 –
FIBRE OPTIC INTERCONNECTING DEVICES AND PASSIVE COMPONENTS –
MECHANICAL SPLICES AND FUSION SPLICE PROTECTORS
FOR OPTICAL FIBRES AND CABLES –
Part 1: Generic specification
1 Scope
This part of IEC 61073 applies to fibre optic splice hardware (mechanical splices and fusion
splice protections) for optical fibres and cables.
It includes:
– fibre optic splice hardware requirements;
– quality assessment procedures.
This standard does not cover test and measurement procedures, which are described in
IEC 61300-1, IEC 61300-2 series and IEC 61300-3 series.
2 Normative references
The following referenced documents are indispensable for the application of this document. For
dated references, only the edition cited applies. For undated references, the latest edition of
the referenced document (including any amendments) applies.
References made to a specific clause or subclause of a standard include all subclauses of the
reference unless otherwise specified.
IEC QC 001002-3, IEC Quality Assessment System for Electronic Components (IECQ) – Rules
of Procedure – Part 3: Approval procedures
IEC Guide 102, Electronic components – Specification structures for quality assessment
(Qualification approval and capability approval)
IEC 60027 (all parts), Letter symbols to be used in electrical technology
IEC 60050-731, International Electrotechnical Vocabulary – Chapter 731: Optical fibre
communication
IEC 60617 (all parts), Graphical symbols for diagrams
IEC 60695-11-5, Fire hazard testing – Part 11-5: Test flames – Needle-flame test method –
Apparatus, confirmatory test arrangement and guidance
IEC 60793-1 (all parts), Optical fibres – Measurement methods and test procedures
IEC 60825-1, Safety of laser products – Part 1: Equipment classification and requirements
IEC 61300-1, Fibre optic interconnecting devices and passive components – Basic test and
measurement procedures – Part 1: General and guidance
---------------------- Page: 11 ----------------------
SIST EN 61073-1:2009
– 6 – 61073-1 © IEC:2009(E)
IEC 61300-2 (all parts), Fibre optic interconnecting devices and passive components – Basic
test and measurement procedures – Part 2: Tests
IEC 61300-3 (all parts), Fibre optic interconnecting devices and passive components – Basic
test and measurement procedures – Part 3: Examinations and measurements
IEC 61930: Fibre optic graphical symbology
IEC 61931, Fibre optic – Terminology
ISO 129-1, Technical drawings – Indication of dimensions and tolerances – Part 1: General
principles
ISO 286-1, ISO system of limits and fits – Part 1: Bases of tolerances, deviations and fits
ISO 1101, Geometrical Product Specifications (GPS) – Geometrical tolerancing – Tolerances of
form, orientation, location and run-out
ISO 8601, Data elements and interchange formats – Information interchange – Representation
of dates and times
3 Terms and definitions
For the purposes of this document, the terms and definitions contained in IEC 60050-731,
IEC 61931, and IEC 60874-1 as well as the following definitions apply.
3.1
cable joint
protective joint of two or more optical fibre cables. It may consist of fibre splices, organizers
and closures
3.2
capillary mechanical splice
mechanical splice where the fibres are aligned by inserting them in a precision capillary tube
3.3
fibre splice
permanent or separable splice (see separable splice)
3.4
fusion splice
splice in which fibre ends are joined in a permanent manner by means of fusion
3.5
hybrid splice
cable splice with fibre splice(s) and electrical conductor splice(s)
3.6
interchangeable splice sets
splice sets are considered to be interchangeable when they both have the same installation
geometry and functional performance
3.7
mechanical splice
splice in which the fibre ends are joined either permanently or separably by any mechanical
means as long as the fibre ends are not fused together
---------------------- Page: 12 ----------------------
SIST EN 61073-1:2009
61073-1 © IEC:2009(E) – 7 –
3.8
permanent splice
splice which cannot be separated
3.9
precision rods mechanical splice
mechanical splice where the fibres are aligned using two or more precision rods
3.10
separable splice
splice which can be disassembled and reassembled but is intended for permanent use
3.11
shape memory alloy splice
mechanical splice where the fibres are aligned by using special materials which have the
property to regain their original macroscopic shape when they are heated up (shape memory
effect) or after an applied load is released, at higher temperature (superelasticity)
3.12
splice protector
protection of bare fibre after the primary coating has been stripped off for the splice procedure
NOTE Additionally, the splice protector reinforces the splice area and provides a possibility to mount this in a
holder.
3.13
splice sub-family
range of fibre optic splice technologies as defined in the relevant specification
3.14
V- groove mechanical splice
mechanical splice where the fibres are aligned by using a precision V-groove
4 Requirements
The requirements for fibre optic splice hardware and accessories covered by this specification
are specified in this clause and in the relevant specification.
4.1 Classification
Fibre optic splice hardware and accessories are classified, either totally or in part, by the
following categories (see Table 1):
– type;
– arrangement ;
– style;
– variant;
– assessment level;
– normative reference extensions.
See Table 1 for an example of a complete fibre optic splice hardware classification.
---------------------- Page: 13 ----------------------
SIST EN 61073-1:2009
– 8 – 61073-1 © IEC:2009(E)
Table 1 – Example of a typical mechanical splice
and fusion splice protection hardware
Type Name: V-groove mechanical splice Name: fusion splice protection
Type of splice: mechanical splice Type of splice: fusion splice hardware
Configuration: separable splice Configuration: permanent splice
Arrangement Kit arrangement with assembling tool Splice protection kit
Style Splice method: V-groove Fibre category: B1, A1
Alignment method: cladding (outside surface, axis) Single fibre protection
Number of simultaneously spliced fibres: one or Splice protection: shrinkable tubing
more
Index matching: gel
Fibre coating removal: required, mechanical
Splice protection hardware: sandwich or others
Variants …………….…. ……………….
4.1.1 Type
Mechanical splices and fibre optic splice hardware shall be defined by the following items.
– Type name
Example: “brand name” mechanical splice
“brand name” splice protector
– Type of splice
Examples: mechanical splice
fusion splice hardware
– Configuration
Examples: permanent splice
separable splice
4.1.2 Arrangement
The fibre optic splice hardware arrangement shall define the delivered form of the item and the
assembling tool, if needed.
Examples: kit arrangement
splice hardware arrangement
4.1.3 Style
Fibre optic splice style shall be defined by the following items, which may differ depending on
the type of splice hardware.
4.1.3.1 Mechanical splice
Fibre category (according to the series IEC 60793-1)
– Splice method
Examples: V-groove
---------------------- Page: 14 ----------------------
SIST EN 61073-1:2009
61073-1 © IEC:2009(E) – 9 –
capillary tube
ferrule/sleeve
shape memory-based shrinkable tube
precision rod
adhesive bonding
crimping
– Alignment method
Examples: cladding (outside surface, axis)
core (transmitted power, visual)
self-alignment
secondary reference surface (for example termini)
– Number of simultaneously spliced fibres
Examples: single/multiple (state the maximum number)
– Index matching
Examples gel
fluid
cured resin
none
– Fibre coating removal
Examples: not required
required • mechanical
• chemical
4.1.3.2 Fusion splice
– Fibre category (according to the series IEC 60793-1)
– Number of simultaneously spliced fibres
Examples: single
multiple (state the maximum number)
4.1.3.3 Splice protection hardware
Examples: shrinkable tubing
capillary tubing
metal crimping
gel or fluid
cured resin
injection moulding
sandwich
soft layer
4.1.4 Variant
The splice hardware variants shall define additional features of structurally similar components
(see 3.2).
---------------------- Page: 15 ----------------------
SIST EN 61073-1:2009
– 10 – 61073-1 © IEC:2009(E)
Examples of feature variables which creates variants:
additional fibre and coating sizes accommodated
alternative mounting or fixing points
4.1.5 Assessment level
Assessment level defines the inspection levels and the acceptable quality level (AQL) of
groups A and B and the periodicity of inspection of groups C and D. Detail specifications shall
specify one or more assessment levels, each of which shall be designated by a capital letter.
The following are preferred levels.
– Assessment level A
• Group A inspection: inspection level II, AQL = 4 %
• Group B inspection: inspection level II, AQL = 4 %
• Group C inspection: 24-month periods
• Group D inspection: 48-month periods
– Assessment level B
• Group A inspection: inspection level II, AQL = 1 %
• Group B inspection: inspection level II, AQL = 1 %
• Group C inspection: 18-month periods
• Group D inspection: 36-month periods
– Assessment level C
• Group A inspection: inspection level II, AQL = 0,4 %
• Group B inspection: inspection level II, AQL = 0,4 %
• Group C inspection: 12-month periods
• Group D inspection: 24-month periods
4.1.6 Normative reference extensions
Normative reference extensions are utilised to identify integration of independent standards
specifications or other reference documents into blank detail specifications.
Unless specified exception is noted, additional requirements imposed by an extension are
mandatory. Usage is primarily intended to merge associated components to form hybrid
devices, or can involve integrated functional application requirements that are dependent on
technical expertise other than fibre optics.
Published reference documents produced by ITU consistent with the scope statements of the
relevant IEC specification series may be utilised as extensions. Published documents produced
by other regional standardisation bodies such as TIA, ETSI, JIS, etc., may be referenced in an
informative annex attached to the generic specification.
Some optical fibre splice configurations require special qualification provisions that are not
necessary to impose universally. These accommodate individual component design
configurations, specialised field tooling, or specific application processes. In such cases,
requirements may be necessary to assure repeatable performance or adequate safety, and
provide additional guidance for complete product specification. These extensions are
mandatory whenever utilised to prepare, assemble or install an optical fibre splice, either for
field application usage or preparation of qualification test specimens. The relevant specification
shall clarify all stipulations. However, design- and style-dependent extensions shall not b
...