SIST EN 15870:2009

Adhesives - Determination of tensile strength of butt joints (ISO 6922:1987 modified)

SIST EN 15870:2009

Name:SIST EN 15870:2009   Standard name:Adhesives - Determination of tensile strength of butt joints (ISO 6922:1987 modified)
Standard number:SIST EN 15870:2009   language:English language
Release Date:09-Jun-2009   technical committee:IPMA - Polimer materials and products
Drafting committee:   ICS number:83.180 - Adhesives
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.Klebstoffe - Bestimmung der Zugfestigkeit von Stumpfklebungen (ISO 6922:1987 modifiziert)Adhésifs - Détermination de la résistance en traction des joints bout à bout (ISO 6922:1987 modifiée)Adhesives - Determination of tensile strength of butt joints (ISO 6922:1987 modified)83.180LepilaAdhesivesICS:Ta slovenski standard je istoveten z:EN 15870:2009SIST EN 15870:2009en,fr,de01-julij-2009SIST EN 15870:2009SLOVENSKI
STANDARDSIST EN 26922:19981DGRPHãþD



SIST EN 15870:2009



EUROPEAN STANDARDNORME EUROPÉENNEEUROPÄISCHE NORMEN 15870April 2009ICS 83.180Supersedes EN 26922:1993
English VersionAdhesives - Determination of tensile strength of butt joints (ISO6922:1987 modified)Adhésifs - Détermination de la résistance en traction desjoints bout à bout (ISO 6922:1987 modifiée)Klebstoffe - Bestimmung der Zugfestigkeit vonStumpfklebungen (ISO 6922:1987 modifiziert)This European Standard was approved by CEN on 26 March 2009.CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this EuropeanStandard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such nationalstandards may be obtained on application to the CEN Management Centre or to any CEN member.This European Standard exists in three official versions (English, French, German). A version in any other language made by translationunder the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as theofficial versions.CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.EUROPEAN COMMITTEE FOR STANDARDIZATIONCOMITÉ EUROPÉEN DE NORMALISATIONEUROPÄISCHES KOMITEE FÜR NORMUNGManagement Centre:
Avenue Marnix 17,
B-1000 Brussels© 2009 CENAll rights of exploitation in any form and by any means reservedworldwide for CEN national Members.Ref. No. EN 15870:2009: ESIST EN 15870:2009



EN 15870:2009 (E) 2 Contents Page Foreword .3 1 Scope .4 2 Normative references .4 3 Principle .4 4 Apparatus .4 5 Test specimens .5 5.1 Adherends .5 5.2 Dimensions of joints .6 5.3 Bonding .6 5.4 Number of test specimens .6 6 Conditioning and test atmosphere .6 7 Procedure .6 8 Expression of results .7 9 Tests report .7 Bibliography .8
SIST EN 15870:2009



EN 15870:2009 (E) 3 Foreword This document (EN 15870:2009) has been prepared by Technical Committee CEN/TC 193 “Adhesives”, the secretariat of which is held by AENOR. This European Standard shall be given the status of a national standard, either by publication of an identical text or by endorsement, at the latest by October 2009, and conflicting national standards shall be withdrawn at the latest by October 2009. Attention is drawn to the possibility that some of the elements of this document may be the subject of patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such patent rights. This document supersedes EN 29622:1993. Safety statement Persons using this document should be familiar with the normal laboratory practice, if applicable. This document cannot address all of the safety problems, if any, associated with its use. It is the responsibility of the user to establish appropriate safety and health practices and to ensure compliance with any regulatory conditions. Environmental statement It is understood that some of the material permitted in this standard may have negative environmental impact. As technological advantages lead to better alternatives for these materials, they will be eliminated from this standard to the extent possible. At the end of the test, the user of the standard shall take care to carry out an appropriate disposal of the wastes, according to local regulation. According to the CEN/CENELEC Internal Regulations, the national standards organizations of the following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom. SIST EN 15870:2009



EN 15870:2009 (E) 4 1 Scope This European Standard specifies a method for determining the bond strength of a butt joint when subjected to tensile force. The method can be applied to all types of adhesives. Although primarily intended for use under ambient conditions, the basic method can also be applied to testing under a wide range of temperature and other environmental conditions. The method requires rigid adherends that can be produced to the required dimensional tolerances and that will withstand the forces applied to them during the test. 2 Normative references The following referenced documents are indispensable for the application of this document. For dated references, only the edition cited applies. For undated references, the latest edition of the referenced document (including any amendments) applies. EN 13887 - Structural Adhesives - Guidelines for surface preparation of metals and plastics prior to adhesive bonding EN ISO 291, Plastics - Standard atmospheres for conditioning and testing (ISO 291:2008) EN ISO 7500-1, Metallic materials – Verification of static uniaxial testing machines – Part 1: Tension/compression testing machines – Verification and calibration of the force-measuring system (ISO 7500-1:2004) EN ISO 10365, Adhesives - Designation of main failure patterns (ISO 10365:1992) 3 Principle A joint formed from two bar or rod adherends bonded by faces normal to their length is stressed to rupture by a tensile f
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27