|
SIST EN 4636:2009
01-september-2009
Aeronavtika - Vijaki, 100° ugrezna glava, šestzoba vdolbina, kratek navoj, iz
titanove zlitine TI-P64001, z aluminijem pigmentiranim premazom - Klasifikacija:
1100 MPa (pri temperaturi okolice)/315 °C
Aerospace series - Screws, 100° countersunk head, six lobe recess, short thread, in
titanium alloy TI-P64001, with aluminium pigmented coating - Classification: 1 100 MPa
(at ambient temperature) / 315 °C
Luft- und Raumfahrt - 100° Senkschrauben, kurzes Gewinde, Sechs-Bogenzahn,aus
Titanlegierung TI-P64001, mit aluminium pigmentierter Beschichtung - Klasse: 1 100
MPa (bei Raumtemperatur) / 315 °C
Série aérospatiale - Vis, 100° à tête fraisée, à filetage court, à empreinte six lobes,en
alliage de titane TI-P64001, avec revêtement alumino-organique - Classification: 1 100
MPa (à température ambiante) / 315 °C
Ta slovenski standard je istoveten z: EN 4636:2009
ICS:
49.025.20 Aluminij Aluminium
49.025.30 Titan Titanium
49.030.20 Sorniki, vijaki, stebelni vijaki Bolts, screws, studs
SIST EN 4636:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 4636:2009
---------------------- Page: 2 ----------------------
SIST EN 4636:2009
EUROPEAN STANDARD
EN 4636
NORME EUROPÉENNE
EUROPÄISCHE NORM
June 2009
ICS 49.030.10
English Version
Aerospace series - Screws, 100° countersunk head, six lobe
recess, short thread, in titanium alloy TI-P64001, with aluminium
pigmented coating - Classification: 1 100 MPa (at ambient
temperature) / 315 °C
Série aérospatiale - Vis, 100° à tête fraisée, à filetage Luft- und Raumfahrt - 100° Senkschrauben, kurzes
court, à empreinte six lobes,en alliage de titane TI-P64001, Gewinde, Sechs-Bogenzahn,aus Titanlegierung TI-P64001,
avec revêtement alumino-organique - Classification: 1 100 mit aluminium pigmentierter Beschichtung - Klasse: 1 100
MPa (à température ambiante) / 315 °C MPa (bei Raumtemperatur) / 315 °C
This European Standard was approved by CEN on 20 March 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 4636:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 4636:2009
EN 4636:2009 (E)
Contents Page
Foreword .3
1 Scope .4
2 Normative references .4
3 Required characteristics .4
3.1 Configuration – Dimensions – Tolerances – Masses .4
3.2 Materials .4
3.3 Surface treatment .5
3.4 Tolerances of form and position .5
4 Designation .6
5 Marking .7
6 Technical specification .7
6.1 General .7
6.2 Approval of manufacturers .7
6.3 Qualification of bolts .7
6.4 Requirement deleted .
...