|
SIST-TS CEN/TS 1455-2:2012
01-september-2012
1DGRPHãþD
SIST ENV 1455-2:2002
Cevni sistemi iz polimernih materialov za (nizko- in visokotemperaturne) odvodne
sisteme v stavbah - Akrilonitril-butadien-stiren (ABS) - 2. del: Navodilo za
ugotavljanje skladnosti
Plastics piping systems for soil and waste discharge (low and high temperature) within
the building structure - Acrylonitrile-butadiene-styrene (ABS) - Part 2: Guidance for the
assessment of conformity
Kunststoff-Rohrleitungssysteme zum Ableiten von Abwasser (niedriger und hoher
Temperatur) innerhalb der Gebäudestruktur - Acrylnitril-Butadien-Styrol (ABS) - Teil 2:
Empfehlungen für die Beurteilung der Konformität
Systèmes de canalisations en plastique pour l'évacuation des eaux-vannes et des eaux
usées (à basse et à haute température) à l'intérieur de la structure des bâtiments —
Acrylonitrile-butadiène-styrène (ABS) — Partie 2: Guide pour l'évaluation de la
conformité
Ta slovenski standard je istoveten z: CEN/TS 1455-2:2012
ICS:
23.040.20 Cevi iz polimernih materialov Plastics pipes
91.140.80 Drenažni sistemi Drainage systems
SIST-TS CEN/TS 1455-2:2012 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST-TS CEN/TS 1455-2:2012
---------------------- Page: 2 ----------------------
SIST-TS CEN/TS 1455-2:2012
TECHNICAL SPECIFICATION
CEN/TS 1455-2
SPÉCIFICATION TECHNIQUE
TECHNISCHE SPEZIFIKATION
May 2012
ICS 23.040.20; 91.140.80 Supersedes ENV 1455-2:2001
English Version
Plastics piping systems for soil and waste discharge (low and
high temperature) within the building structure - Acrylonitrile-
butadiene-styrene (ABS) - Part 2: Guidance for the assessment
of conformity
Systèmes de canalisations en plastique pour l'évacuation Kunststoff-Rohrleitungssysteme zum Ableiten von
des eaux-vannes et des eaux usées (à basse et à haute Abwasser (niedriger und hoher Temperatur) innerhalb der
température) à l'intérieur de la structure des bâtiments - Gebäudestruktur - Acrylnitril-Butadien-Styrol (ABS) - Teil 2:
Acrylonitrile-butadiène-styrène (ABS) - Partie 2: Guide pour Empfehlungen für die Beurteilung der Konformität
l'évaluation de la conformité
This Technical Specification (CEN/TS) was approved by CEN on 9 January 2012 for provisional application.
The period of validity of this CEN/TS is limited initially to three years. After two years the members of CEN will be requested to submit their
comments, particularly on the question whether the CEN/TS can be converted into a European Standard.
CEN members are required to announce the existence of this CEN/TS in the same way as for an EN and to make the CEN/TS available
promptly at national level in an appropriate form. It is permissible to keep conflicting national standards in force (in parallel to the CEN/TS)
until the final decision about the possible conversion of the CEN/TS into an EN is reached.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Croatia, Cyprus, Czech Republic, Denmark, Estonia,
Finland, France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland,
Portugal, Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland, Turkey and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2012 CEN All rights of exploitation in any form and by any means reserved Ref. No. CEN/TS 1455-2:2012: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST-TS CEN/TS 1455-2:2012
CEN/TS 1455-2:2012 (E)
Contents Page
Foreword .3
Introduction .4
1 Scope .5
2 Normative references .5
3 Terms and definitions .5
4 Abbreviated terms .8
5 General .9
6 Testing and inspection .
...