|
SIST EN 933-10:2009
01-oktober-2009
1DGRPHãþD
SIST EN 933-10:2002
3UHVNXVLJHRPHWULþQLKODVWQRVWLDJUHJDWRYGHO8JRWDYOMDQMHILQLKGHOFHY
=UQDYRVWNDPHQHPRNHVHMDQMH]]UDþQLPFXUNRP
Tests for geometrical properties of aggregates - Part 10: Assessment of fines - Grading
of filler aggregates (air jet sieving)
Prüfverfahren für geometrische Eigenschaften von Gesteinskörnungen - Teil 10:
Beurteilung von Feinanteilen - Kornverteilung von Füller (Luftstrahlsiebung)
Essais pour déterminer les caractéristiques géométriques des granulats - Partie 10:
Détermination des fines - Granularité des fillers (tamisage dans un jet d'air)
Ta slovenski standard je istoveten z: EN 933-10:2009
ICS:
91.100.15 Mineralni materiali in izdelki Mineral materials and
products
SIST EN 933-10:2009 en,fr,de
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.
---------------------- Page: 1 ----------------------
SIST EN 933-10:2009
---------------------- Page: 2 ----------------------
SIST EN 933-10:2009
EUROPEAN STANDARD
EN 933-10
NORME EUROPÉENNE
EUROPÄISCHE NORM
July 2009
ICS 91.100.15 Supersedes EN 933-10:2001
English Version
Tests for geometrical properties of aggregates - Part 10:
Assessment of fines - Grading of filler aggregates (air jet
sieving)
Essais pour déterminer les caractéristiques géométriques Prüfverfahren für geometrische Eigenschaften von
des granulats - Partie 10: Détermination des fines - Gesteinskörnungen - Teil 10: Beurteilung von Feinanteilen -
Granularité des fillers (tamisage dans un jet d'air) Kornverteilung von Füller (Luftstrahlsiebung)
This European Standard was approved by CEN on 12 June 2009.
CEN members are bound to comply with the CEN/CENELEC Internal Regulations which stipulate the conditions for giving this European
Standard the status of a national standard without any alteration. Up-to-date lists and bibliographical references concerning such national
standards may be obtained on application to the CEN Management Centre or to any CEN member.
This European Standard exists in three official versions (English, French, German). A version in any other language made by translation
under the responsibility of a CEN member into its own language and notified to the CEN Management Centre has the same status as the
official versions.
CEN members are the national standards bodies of Austria, Belgium, Bulgaria, Cyprus, Czech Republic, Denmark, Estonia, Finland,
France, Germany, Greece, Hungary, Iceland, Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal,
Romania, Slovakia, Slovenia, Spain, Sweden, Switzerland and United Kingdom.
EUROPEAN COMMITTEE FOR STANDARDIZATION
COMITÉ EUROPÉEN DE NORMALISATION
EUROPÄISCHES KOMITEE FÜR NORMUNG
Management Centre: Avenue Marnix 17, B-1000 Brussels
© 2009 CEN All rights of exploitation in any form and by any means reserved Ref. No. EN 933-10:2009: E
worldwide for CEN national Members.
---------------------- Page: 3 ----------------------
SIST EN 933-10:2009
EN 933-10:2009 (E)
Contents Page
Foreword . 3
1 Scope. 4
2 Normative references . 4
3 Terms and definitions . 4
4 Principle . 4
5 Apparatus . 5
6 Preparation of test portions . 5
7 Procedure . 5
8 Calculation and expression of results . 6
9 Test report . 7
9.1 Required data . 7
9.2 Optional data . 7
Annex A (informative) Example of a test data sheet . 8
Annex B (informative) Precision . 9
Annex C (informative) Graphical presentation of results . 10
2
---------------------- Page: 4 ----------------------
SIST EN 933-10:2009
EN 933-10:2009 (E)
Foreword
This document (EN 933-10:2009) has been prepared by Technical Committee CEN/TC 154
“Aggregates”, the secretariat of which is held by BSI.
This European Standard shall be given the status of a national standard, either by publication of an
identical text or by endorsement, at the latest by January 2010, and conflicting national standards
shall be withdrawn at the latest by January 2010.
Attention is drawn to the possibility that some of the elements of this document may be the subject of
patent rights. CEN [and/or CENELEC] shall not be held responsible for identifying any or all such
patent rights.
This document supersedes EN 933-10:2001.
This standard forms part of a series of tests for geometrical properties of aggregates. Test methods for
other properties of aggregates are covered by parts of the following European Standards:
EN 932, Tests for general properties of aggregates
EN 1097, Tests for mechanical and physical properties of aggregates
EN 1367, Tests for thermal and weathering properties of aggregates
EN 1744, Tests for chemical properties of aggregates
EN 13179, Tests for filler aggregate used in bituminous mixtures
The other parts of EN 933 will be:
Part 1: Determination of particle size distribution — Sieving method
Part 2: Determination of particle size distribution —- Test sieves, nominal size of apertures
Part 3: Determination of particle shape — Flakiness index
Part 4: Determination of particle shape — Shape index
Part 5: Determination of percentage of crushed and broken surfaces in coarse aggregate particles
Part 6: Assessment of surface characteristics — Flow coefficient for aggregates
Part 7: Determination of shell content — Percentage of shells in coarse aggregates
Part 8: Assessment of fines — Sand equivalent test
Part 9: Assessment of fines — Methylene blue test
Part 11: Classification test for the constituents of coarse recycled aggregate
According to the CEN/CENELEC Internal Regulations, the national standards organizations of the
following countries are bound to implement this European Standard: Austria, Belgium, Bulgaria,
Cyprus, Czech Republic, Denmark, Estonia, Finland, France, Germany, Greece, Hungary, Iceland,
Ireland, Italy, Latvia, Lithuania, Luxembourg, Malta, Netherlands, Norway, Poland, Portugal, Romania,
Slovakia, Slovenia, Spain, Sweden, Switzerland and the United Kingdom.
3
---------------------- Page: 5 ----------------------
SIST EN 933-10:2
...