SIST ISO 13012-1:2009

Rolling bearings - Accessories for sleeve type linear ball bearings - Part 1: Boundary dimensions and tolerances for series 1 and 3

SIST ISO 13012-1:2009

Name:SIST ISO 13012-1:2009   Standard name:Rolling bearings - Accessories for sleeve type linear ball bearings - Part 1: Boundary dimensions and tolerances for series 1 and 3
Standard number:SIST ISO 13012-1:2009   language:English language
Release Date:05-Apr-2009   technical committee:ISEL - Mechanical elements
Drafting committee:   ICS number:21.100.20 - Rolling bearings
SLOVENSKI STANDARD
SIST ISO 13012-1:2009
01-maj-2009
.RWDOQLOHåDML'RGDWNL]DOLQHDUQHNURJOLþQHOHåDMHVNURåHQMHPNURJOLFGHO
=XQDQMHPHUHLQWROHUDQFH]DVHULMLLQ
Rolling bearings - Accessories for sleeve type linear ball bearings - Part 1: Boundary
dimensions and tolerances for series 1 and 3
Wälzlager - Zubehör für Linearlager mit Kugelumlauf und Hülse - Teil 1: Grenzabmaße
und Toleranzen für die Serien 1 und 3
Roulements - Accessoires pour douilles à billes linéaires - Partie 1: Dimensions
d'encombrement et tolérances pour les séries 1 et 3
Ta slovenski standard je istoveten z: ISO 13012-1:2009
ICS:
21.100.20 Kotalni ležaji Rolling bearings
SIST ISO 13012-1:2009 en,fr
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 13012-1:2009

---------------------- Page: 2 ----------------------

SIST ISO 13012-1:2009

INTERNATIONAL ISO
STANDARD 13012-1
First edition
2009-02-01


Rolling bearings — Accessories for
sleeve type linear ball bearings —
Part 1:
Boundary dimensions and tolerances for
series 1 and 3
Roulements — Accessoires pour douilles à billes linéaires —
Partie 1: Dimensions d'encombrement et tolérances pour les séries 1
et 3




Reference number
ISO 13012-1:2009(E)
©
ISO 2009

---------------------- Page: 3 ----------------------

SIST ISO 13012-1:2009
ISO 13012-1:2009(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but
shall not be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In
downloading this file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat
accepts no liability in this area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation
parameters were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In
the unlikely event that a problem relating to it is found, please inform the Central Secretariat at the address given below.


COPYRIGHT PROTECTED DOCUMENT


©  ISO 2009
or by any means,
electronic or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or
ISO's member body in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [email protected]
Web www.iso.org
Published in Switzerland

ii © ISO 2009 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 13012-1:2009
ISO 13012-1:2009(E)
Contents Page
Foreword. iv
Introduction . v
1 Scope .1
2 Normative references .1
3 Terms and definitions .2
4 Symbols .3
4.1 Closed and adjustable flangeless housings for series 1 sleeve type linear ball bearings.3
4.2 Closed and adjustable flanged housings for series 3 sleeve type linear ball bearings.3
4.3 Open flanged housings for series 3 sleeve type linear ball bearings.4
4.4 Closed and adjustable flangeless housings for series 3 sleeve type linear ball bearings.4
4.5 Open and open adjustable flangeless housings for series 3 sleeve type linear ball
bearings .4
4.6 Standard height shaft support rails for series 3 sleeve type linear ball bearings .5
4.7 Low height shaft support rails for series 3 sleeve type linear ball bearings .5
4.8 Flanged shaft support blocks fo
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27