SIST ISO 12130-3:2002

Plain bearings -- Hydrodynamic plain tilting pad thrust bearings under steady-state conditions -- Part 3: Guide values for the calculation of tilting pad thrust bearings

SIST ISO 12130-3:2002

Name:SIST ISO 12130-3:2002   Standard name:Plain bearings -- Hydrodynamic plain tilting pad thrust bearings under steady-state conditions -- Part 3: Guide values for the calculation of tilting pad thrust bearings
Standard number:SIST ISO 12130-3:2002   language:English language
Release Date:30-Nov-2002   technical committee:ISEL - Mechanical elements
Drafting committee:   ICS number:21.100.10 - Plain bearings
SLOVENSKI STANDARD
SIST ISO 12130-3:2002
01-december-2002
'UVQLOHåDML+LGURGLQDPLþQLGUVQLVDPRSULODJRGOMLYLDNVLDOQLVHJPHQWQLOHåDMLSUL
VWDFLRQDUQLKSRJRMLKREUDWRYDQMDGHO3ULSRURþHQHYUHGQRVWL]DSUHUDþXQ
VDPRSULODJRGOMLYLKDNVLDOQLKVHJPHQWQLKOHåDMHY
Plain bearings -- Hydrodynamic plain tilting pad thrust bearings under steady-state
conditions -- Part 3: Guide values for the calculation of tilting pad thrust bearings
Paliers lisses -- Butées hydrodynamiques à patins oscillants fonctionnant en régime
stationnaire -- Partie 3: Paramètres opérationnels admissibles pour le calcul des butées
à patins oscillants
Ta slovenski standard je istoveten z: ISO 12130-3:2001
ICS:
21.100.10 Drsni ležaji Plain bearings
SIST ISO 12130-3:2002 en
2003-01.Slovenski inštitut za standardizacijo. Razmnoževanje celote ali delov tega standarda ni dovoljeno.

---------------------- Page: 1 ----------------------

SIST ISO 12130-3:2002

---------------------- Page: 2 ----------------------

SIST ISO 12130-3:2002


INTERNATIONAL ISO
STANDARD 12130-3
First edition
2001-11-15


Plain bearings — Hydrodynamic plain
tilting pad thrust bearings under steady-
state conditions —
Part 3:
Guide values for the calculation of tilting
pad thrust bearings
Paliers lisses — Butées hydrodynamiques à patins oscillants fonctionnant
en régime stationnaire —
Partie 3: Paramètres opérationnels admissibles pour le calcul des butées à
patins oscillants



Reference number
ISO 12130-3:2001(E)
©
 ISO 2001

---------------------- Page: 3 ----------------------

SIST ISO 12130-3:2002
ISO 12130-3:2001(E)
PDF disclaimer
This PDF file may contain embedded typefaces. In accordance with Adobe's licensing policy, this file may be printed or viewed but shall not
be edited unless the typefaces which are embedded are licensed to and installed on the computer performing the editing. In downloading this
file, parties accept therein the responsibility of not infringing Adobe's licensing policy. The ISO Central Secretariat accepts no liability in this
area.
Adobe is a trademark of Adobe Systems Incorporated.
Details of the software products used to create this PDF file can be found in the General Info relative to the file; the PDF-creation parameters
were optimized for printing. Every care has been taken to ensure that the file is suitable for use by ISO member bodies. In the unlikely event
that a problem relating to it is found, please inform the Central Secretariat at the address given below.


©  ISO 2001
or by any means, electronic
or mechanical, including photocopying and microfilm, without permission in writing from either ISO at the address below or ISO's member body
in the country of the requester.
ISO copyright office
Case postale 56 • CH-1211 Geneva 20
Tel. + 41 22 749 01 11
Fax + 41 22 749 09 47
E-mail [email protected]
Web www.iso.ch
Printed in Switzerland

ii © ISO 2001 – All rights reserved

---------------------- Page: 4 ----------------------

SIST ISO 12130-3:2002
ISO 12130-3:2001(E)
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards bodies (ISO
member bodies). The work of preparing International Standards is normally carried out through ISO technical
committees. Each member body interested in a subject for which a technical committee has been established has
the right to be represented on that committee. International organizations, governmental and non-governmental, in
liaison with ISO, also take part in the work. ISO collaborates closely with the International Electrotechnical
Commission (IEC) on all matters of electrotechnical standardization.
International Standards are drafted in accordance with the rules given in the ISO/IEC Directives, Part 3.
Draft International Standards adopted by the technical committees are circulated to the member bodies for voting.
Publication as an International Standard requires approval by at least 75 % of the member bodies casting a vote.
Attention is drawn to the possibility that some of the elements of this part of ISO 12130 may be the subject of
patent rights. ISO shall not be held responsible for identifying any or all such patent rights.
International Standard ISO 12130-3 was prepared by Technical Committee ISO/TC 123, Plain bearings,
Subcommittee SC 4, Methods of calculation of plain bearings.
ISO 12130 consists of the following parts, under the general title Plain bearings — Hydrodynamic plain tilting pad
thrust bearings under steady-state conditions:
 Part 1: Calculation of tilting pad thrust bearings
 Part 2: Functions for calculation of tilting pad thrust bearings
 Part 3: Guide values for the calculation of tilting pad thrust bearings
© ISO 2001 – All rights reserved iii

---------------------- Page: 5 ----------------------

S
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27