|
INTERNATIONAL ISO
STANDARD 5618-1
First edition
2023-11
Fine ceramics (advanced ceramics,
advanced technical ceramics) —
Test method for GaN crystal surface
defects —
Part 1:
Classification of defects
Céramiques techniques — Méthode d’essai pour les défauts de surface
des cristaux de GaN —
Partie 1: Classification des défauts
Reference number
© ISO 2023
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester.
ISO copyright office
CP 401 • Ch. de Blandonnet 8
CH-1214 Vernier, Geneva
Phone: +41 22 749 01 11
Email: [email protected]
Website: www.iso.org
Published in Switzerland
ii
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Classification of defects . 3
4.1 General . 3
4.2 Description of the defect classes . 3
4.2.1 Dislocation . 3
4.2.2 Process-induced defects . 5
Bibliography . 7
iii
Foreword
ISO (the International Organization for Standardization) is a worldwide federation of national standards
bodies (ISO member bodies). The work of preparing International Standards is normally carried out
through ISO technical committees. Each member body interested in a subject for which a technical
committee has been established has the right to be represented on that committee. International
organizations, governmental and non-governmental, in liaison with ISO, also take part in the work.
ISO collaborates closely with the International Electrotechnical Commission (IEC) on all matters of
electrotechnical standardization.
The procedures used to develop this document and those intended for its further maintenance are
described in the ISO/IEC Directives, Part 1. In particular, the different approval criteria needed for the
different types of ISO document should be noted. This document was drafted in accordance with the
editorial rules of the ISO/IEC Directives, Part 2 (see www.iso.org/directives).
ISO draws attention to the possibility that the implementation of this document may involve the use
of (a) patent(s). ISO takes no position concerning the evidence, validity or applicability of any claimed
patent rights in respect thereof. As of the date of publication of this document, ISO had not received
notice of (a) patent(s) which may be required to implement this document. However, implementers are
cautioned that this may not represent the latest information, which may be obtained from the patent
database available at www.iso.org/patents. ISO shall not be held responsible for identifying any or all
such patent rights.
Any trade name used in this document is information given for the convenience of users and does not
constitute an endorsement.
For an explanation of the voluntary nature of standards, the meaning of ISO specific terms and
expressions related to conformity assessment, as well as information about ISO's adherence to
the World Trade Organization (WTO) principles in the Technical Barriers to Trade (TBT), see
www.iso.org/iso/foreword.html.
This document was prepared by Technical Committee ISO/TC 206, Fine ceramics.
A list of all parts in the ISO 5618 series can be found on the ISO website.
Any feedback or questions on this document should be directed to the user’s national standards body. A
complete listing of these bodies can be found at www.iso.org/members.html.
iv
Introduction
GaN is a direct transition type of wide-bandgap semiconductor with superior physical properties,
including a higher breakdown electric field, saturated electron drift velocity and thermal conductivity,
to Si. GaN is expected to be applied not only in light-emitting devices that have been in practical use
for a long time, such as ultraviolet and blue laser diodes (LDs) and light-emitting diodes (LEDs), but
also in power devices for high-efficiency power conversion. In particular, the characteristics of GaN-
based power devices are applied in the fields of photovoltaics, automobiles, railways (electric motors
and linear motors), communication base stations and microwave power transmission.
The single-crystal GaN substrate or single-crystal GaN film is the base material used to produce
devices. However, the surface of a single-crystal GaN substrate or single-crystal GaN film contains
many dislocations that are introduced during crystal growth and defects that are introduced during
wafer processing. The dislocations and/or defects cause a decrease in luminous efficiency for a light-
emitting device and a degradation in performance and reliability for a power device. In particular,
given the practical applications and market expansion of power devices that apply a high voltage and
high current, it is important to supply single-crystal GaN substrates and single-crystal GaN films with
low densities of dislocation and defects. Therefore, it is essential to have an International Standard that
defines and classifies the types of, and further determines the density of, dislocations and process-
induced defects that exist on the surface as an index for assessing the quality of a single-crystal GaN
substrate or single-crystal GaN film.
This document gives a classification of the dislocations and process-induced defects exposed on the
surface of single-crystal GaN substrates and single-crystal GaN films. These single-crystal substrates
and films are mainly used for light-emitting devices, such as LDs and LEDs, and power devices
1)
that perform high-voltage and high-current power conversion. ISO 5618-2 provides a method of
determining the etch pit density.
1) Under preparation. Stage at the time of publication: ISO/DIS 5618-2:2023.
v
INTERNATIONAL STANDARD ISO 5618-1:2023(E)
Fine ceramics (advanced ceramics, advanced technical
ceramics) — Test method for GaN crystal surface defects —
Part 1:
Classification of defects
1 Scope
This document gives a classification of the dislocations and process-induced defects, from among the
various surface defects, that occur on single-crystal gallium nitride (GaN) substrates or single-crystal
GaN films.
It is applicable to the dislocations and process-induced defects exposed on the surface of the following
types of GaN substrates or films:
— single-crystal GaN substrate;
— single-crystal GaN film formed by homoepitaxial growth on a single-crystal GaN substrate;
— single-crystal GaN film formed by heteroepitaxial growth on a single-
...