ISO/ASTM 52927:2024

Additive manufacturing — General principles — Main characteristics and corresponding test methods

ISO/ASTM 52927:2024

Name:ISO/ASTM 52927:2024   Standard name:Additive manufacturing — General principles — Main characteristics and corresponding test methods
Standard number:ISO/ASTM 52927:2024   language:English language
Release Date:18-Mar-2024   technical committee:ISO/TC 261 - Additive manufacturing
Drafting committee:ISO/TC 261/JG 76 - Joint ISO/TC 261-ASTM F 42 Group : Revision of ISO 17296-3 & ASTM F3122-14   ICS number:25.030 - Additive manufacturing
International
Standard
ISO/ASTM 52927
First edition
Additive manufacturing — General
2024-03
principles — Main characteristics
and corresponding test methods
Fabrication additive — Principes généraux — Principales
caractéristiques et méthodes d'essai correspondantes
Reference number
ISO/ASTM 52927:2024(en) © ISO/ASTM International 2024

---------------------- Page: 1 ----------------------
ISO/ASTM 52927:2024(en)
COPYRIGHT PROTECTED DOCUMENT
© ISO/ASTM International 2024
All rights reserved. Unless otherwise specified, or required in the context of its implementation, no part of this publication may
be reproduced or utilized otherwise in any form or by any means, electronic or mechanical, including photocopying, or posting on
the internet or an intranet, without prior written permission. Permission can be requested from either ISO at the address below
or ISO’s member body in the country of the requester. In the United States, such requests should be sent to ASTM International.
ISO copyright office ASTM International
CP 401 • Ch. de Blandonnet 8 100 Barr Harbor Drive, PO Box C700
CH-1214 Vernier, Geneva West Conshohocken, PA 19428-2959, USA
Phone: +41 22 749 01 11 Phone: +610 832 9634
Fax: +610 832 9635
Email: [email protected] Email: [email protected]
Website: www.iso.org Website: www.astm.org
Published in Switzerland

© ISO/ASTM International 2024 – All rights reserved
ii

---------------------- Page: 2 ----------------------
ISO/ASTM 52927:2024(en)
Contents Page
Foreword .iv
Introduction .v
1 Scope . 1
2 Normative references . 1
3 Terms and definitions . 1
4 Main characteristics and corresponding test methods . 2
4.1 General .2
4.2 Selection criteria .2
5 Part and process testing — Specifications and quality criteria . 3
5.1 General .3
5.2 Testing the feedstocks .3
5.3 Monitoring the process .3
5.4 Testing the part .3
Annex A (normative) Test methods for metallic materials . 4
Annex B (normative) Test methods for polymer materials .10
Annex C (normative) Test methods for ceramic materials . 14
Bibliography .
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27