ISO/R 464:1965

Title missing - Legacy paper document

ISO/R 464:1965

Name:ISO/R 464:1965   Standard name:Title missing - Legacy paper document
Standard number:ISO/R 464:1965   language:English language
Release Date:31-Dec-1964   technical committee:ISO/TMBG - Technical Management Board - groups
Drafting committee:ISO/TMBG - Technical Management Board - groups   ICS number:
UDC 621.822
Ref. No.: IÇO/R 464 - 1965 (E)
IS0
I N T ERN AT I O N A L ORGAN I Z AT I O N FOR STAND A RD IZATl O N
IS0 RECO M M END AT10 N
R 464
ROLLING BEARINGS
BEARINGS WITH LOCATING SNAP RING
DIMENSIONS
1st EDITION
Decem ber 1965
COPYRIGHT RESERVED
The copyright of IS0 Recommendations and IS0 Standards
belongs to IS0 Member Bodies. Reproduction of these
documents, in any country, may be authorized therefore only
by the national standards organization of that country, being
a member of ISO.
For each individual country the only valid standard is the national standard of that country.
Printed in Switzerland
Also issued in French and Russian. Copies to be obtained through the national standards organizations.

---------------------- Page: 1 ----------------------
BRIEF HISTORY
The IS0 Recommendation R 464, Rolling Bearings. Bearings with Locating Snap Ring.
Dimensions, was drawn up by Technical Committee ISO/TC 4, Rolling Bearings, the Secretariat
of which is held by the Sveriges Standardiseringskommission (SIS).
This 1SO Recommendation cancels and replaces section 4 of the IS0 Recommendation
R 15-1955, Ball and Roller Bearings.
Work on this question by the Technical Committee began in 1956 and led, in 1962, to the
adoption of a Draft IS0 Recommendation.
In October 1962, this Draft IS0 Recommendation (No. 360) was circulated to all the IS0
Member Bodies for enquiry. It was approved by the following Member Bodies:
Australia France Romania
Germany Spain
Austria
Belgium Hungary Sweden
Brazil India Switzerland
Bu 1 gar i a Ireland United Kingdom
Burma Italy U.S.A.
Japan U.S.S.R.
Canada
Chile Netherlands Yugoslavia
Czechoslovakia New Zealand
No Member Body opposed the approval of the Draft.
The Draft 1SO Recommendation was then submitted by correspondence to the IS0
Council, which decided, in December 1965, to accept it as an IS0 RECOMMENDATION.
-2-

---------------------- Page: 2 ----------------------
ISO/R 464 - 1965 (El
Decem ber 1965
IS0 Recommendation R 464
ROLLING BEARINGS
BEARINGS WITH LOCATING SNAP RING
DIMENSIONS
The snap ring groove dimensions and the snap ring dimensions are given as follows:
................... pages 4 and 5
1. Dimension series 18 and 19
1.1 Snap ring groove dimensions
1.2 Snap ring dimensions
2. Diameter series O, 2, 3 and 4 . pages 6 and 7
(except dimensions series 00, 82 and 83)
2.1 Snap ring groove dimensions
2.2 Snap ring dimensions.
The following symbols are used:
D = bearing outside diameter
il, = snap ring groove diameter
D, = outside diameter of snap ring
a = snap ring groove location
b = snap ring groove width
e -I snap ring section height
f = snap ring thickness
g =- snap ring gap
ro = fillet radii at snap ring groove bottom
f

---------------------- Page: 3 ----------------------
ISO/R 464 - 1965 (E)
1. DIMENSION SERIES 18 AND 19
1.1 Snap ring groove dimensions
Dimensions in millimetres
Distance a
Groove Fillet
Ecaring Diameter
___~~ ~ __~____
width radii
outside
Di Dimension Dimension
h
diameter r0
series 18 series 19
D
Dl max. Dl min. a max. a min. I a max. a min. b max. b min. max.
I
- -
22 20.8 20.5 1.05 0.9 1.05 0.8
0.2
24 22.8 22.5 1 .O5 0.9 0.2
-1 - 1
28 26.7 26.4 1.3 1.15 1*05 1.2 ~ 0:95 0.25
I
- -
30 28.7 28.4 1.3 1.15 1.2 0.95 0.25
-
-
32 30.7 30.4 1.3 1 1.15 1.2 ' 0.95 0.25
- -
34 32.7 32.4
1.2 I 0.95 0.25
lS3 ~ l.15
1.3 ~ 1.15 1.7
37 35.7 35.4 1.55 1.2 1 0.95 0.25
I
- -
37.7 37.4 1.7 1.55
39 1.2 0.95 0.25
- -
40 38.7 38.4 1.3 1.15 1.2 0.95 0.25
42 40.7 40.4 1.3 1.15 1.7 1.55 1.2 0.95 0.25
- -
44 42.7 42.4 1.3 1.15 1.2 0.95 0.25
- -
45 43.7 43.4 1.7 1.55 1.2 0.95 0.25
47 45.7 45.4 1.3 1.15 1.7 1.55 1.2 0.95 0.25
50.4 1.3 1.15 1.7
52 50.7 1.55 1.2 0.95 0.25
- -
53.4 1.7 1.2
55 53.7 1.55 0.95 0.25
- -
56.7 56.4 1.3 1.15 1.2
58 0.95 0.25
- -
62 60.7 60.3 1.7 1.55 1.2 0.95 0.25
- -
65 63.7 63.3 1.3 1.15 1.2 0.95 0.25
- -
68 66.7 66.3 1.7 1.55 1.2 0.95 0.25
72 70.7 70.3 1.7 1.55 1.7 1.55 1.2 0.95 0.25
-
-
78 76.2 75.8 1.7 1.55 1.6 1.3 0.4
-
-
80 77.9 77.5 2.1 1.9 1.6 1.3 0.4
1.7 2.1 1.6
85 82.9 82.5 1.55 1.9 1.3 0.4
87.9 87.5 1.7 1.55 2.1 1.9 1.6
90 13 0.4
- -
92.9 92.5 1.7 1.55 1.6 1.3 0.4
95
1 O0 97.9 97.5 1.7 1.55 2.5 2.3 1.6 1.3 0.4
- -
105 102.6 102.1 2.5 2.3 1.6 1.3 0.4
110 107.6 107.1 2.1 1.9 2.5 2.3 1.6 1.3 0.4
- -
115 112.6 112.1 2.1 1.9 1.6 1.3 0.4
117.6 2.1 1.6
120 117.1 1.9 3.3 3.1 1.3 0.4
122.1 2.1 1.6
125 122.6 1.9 3.3 3.1 1.3 0.4
127.6 127.1 2.1 1.6 1.3 0.4
130 1.9 3.3 3.1
140 137.6 137.1 2.5 2.3 3.3 3.1 2.2 1.9 0.6
- -
145 142.6 142.1 3.3 3.1 2.2 1.9 0.6
150 147.6 147.1 2.5 2.3 3.3 3.1 2.2 1.9 0.6
165 161.8 161.3 3.3 3.1 3.7 3.5 2.2 1.9 0.6
- -
175 171.8 171.3 3.3 3.1 2.2 1.9 0.6
- -
2.2 0.6
180 176.8 176.3 3.7 3.5 1.9
190 186.8 186.3 2.2 0.6
3.3 3.1 3.7 3.5 1.9
- -
200 196.8 196.3 2.2 1.9 0.6
3.3 3.1
Chamfer at groove side of outer ring should clear a fillet radius of
0.3 mm in dimension series 18 up to and including D = 78 mm and
in dimension series 19 up to and including D =
47 mm;
0.5 mm in dimension series 18 over D = 78 mm and
in dimension series 19 over D = 47 mm.
-4-

---------------------- Page: 4 ----------------------
ISO/R 461 - 1965 (E)
1. DIMENSION SERIES 18 AND 19 (concluded)
1.2 Snap ring dimensions
Dimensions in millimetres
Bearing Snap ring section Iieiglit Snap ring thickness
outside
e g*
f
diameter
~~ approx.
D
e max. 1 e min. f max. f min.
22
24.8 2.0 , 1.85 0.7 0.6 2
24 26.8 2.0 1.85 0.7 O. 6 2
28 30.8 2.05 1.9 0.85 0.75 3
30 32.8 2.05 1.9 0.85 0.75 3
32 34.8 2.05 1.9 0.85 0.75 3
34 36.8 2.05 1.9 0.85 0.75 3
37 39.8 2.05
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27