ISO/R 773:1969

Rectangular or square parallel keys and their corresponding keyways (Dimensions in millimetres)

ISO/R 773:1969

Name:ISO/R 773:1969   Standard name:Rectangular or square parallel keys and their corresponding keyways (Dimensions in millimetres)
Standard number:ISO/R 773:1969   language:English language
Release Date:31-Dec-1968   technical committee:ISO/TC 14 - Shafts for machinery and accessories
Drafting committee:ISO/TC 14 - Shafts for machinery and accessories   ICS number:21.120.30 - Keys and keyways, splines
1 //
UDC 621.886.6 : 621.824.44
Ref. No. : ISO/R 773-1969 (E)
IS0
FOR S TA N DARD 1 ZATl O N
I N T ER N AT I ON A L O R G A N I Z AT 1 ON
IS0 RECOMMENDATION
R 773
RECTANGULAR OR SQUARE PARALLEL KEYS
AND THEIR CORRESPONDING KEYWAYS
(Dimensions in millimetres)
1st EDITION
January 1969
c
COPYRIGHT RESERVED
The copyright of IS0 Recommendations and IS0 Standards
IS0 Member Bodies. Reproduction of these
belongs to
documents, in any country, may be authorized therefore oniy
by the national standards organization of that country, being
a member of ISO.
For each individual country the only valid standard is the national standard of that country.
Printed in Switzerland
Also issued in French and Russian. Copies to be obtained through the national standards organizations.

---------------------- Page: 1 ----------------------
BRIEF HISTORY
The IS0 Recommendation R 773, Rectangular or square parallel keys and their corresponding keyways
(Dimensions in millimetres), was drawn up by Technical Committee iSO/TC 16, Keys and keyways, the
Secretariat of which is held by the Institut Belge de Normalisation (IBN).
Work on this question by the Technical Committee led in 1965 to the adoption of a Draft IS0 Recommen-
I dation.
In November 1966, this Draft IS0 Recommendation (No. 1084) was circulated to all the IS0 Member
Bodies for enquiry. It was approved, subject to a few modifications of an editorial nature, by the following
Member Bodies :
Argentina Greece Spain
Austria Hungary Sweden
Belgium India Switzerland
Brazil Italy Turkey
Chile Japan U.A.R.
Denmark Korea, Rep. of United Kingdom
France Netherlands U.S.S.R.
Germany South Africa, Rep. of Yugoslavia
No Member Body opposed the approval of the Draft.
The Draft IS0 Recommendation was then submitted by correspondence to the IS0 Council, which decided.
in January 1969, to accept it as an IS0 RECOMMENDATION.
3-

---------------------- Page: 2 ----------------------
=
ISO/R 773-1969 (E)
I SO Recommendation R 773 January 1969
RECTANGULAR OR SQUARE PARALLEL KEYS
AND THEIR CORRESPONDING KEYWAYS
(Dimensions in millimetres)
1. SCOPE
This IS0 Recommendation specifies the dimensional characteristics of rectangular or square parallel keys and of
their corresponding keyways in shaft and hub. It also gives the relations which should be observed between the
diameter of shaft and section of key.
2. FIELD OF APPLICATION
This IS0 Recommendation is for general purposes, for cylindrical shaft ends*, but it is recommended that the
values given be adhered to even for special applications.
Attention is drawn to the fact that some IS0 Recommendations, published previously, give dimensions and
tolerances other than those appearing in the present 1SO Recommendation.
DIMENSIONS AND TOLERANCES OF KEYS
3.
Form A Form E Form C
Section X-.Y
3
*
The relation between the diameter of conical shaft end and key section is given in IS0 Recommendation R 775, Cylindrical
and 1/10 conical shaft ends.
-4-

---------------------- Page: 3 ----------------------
ISO/R 773-1%9 (E
Dimensions in millimetres
Range of lengths
Width Thickness Chamfer
I h S I **
h
Tolerance
min. max. from to
nominal Tolerance*
nominal 1 h9
0.16 0.25 6 20
0.16 0.25 6 36
0.16 0.25 8 45
0.25 0.40 10 56
14 70
0.25 0.40
18
8 7 0.25 0.40 90
0
- 0.036 8
22
0.40 0.60 Il0
10
0
8 0.40 0.60 28 140
12
- 0.090
9 O .40 0.60 36 160
14
O
- 0.043
0.40 0.60 45 180
16 10
0.40 50
0.60 200
0.60 0.80 56
220
0.60 0.80 63 250
0.60 0.80 70 280
0.60 0.80 80 320
0.60 0.80 90 360
1 .O0 1.20 1 O0 400
- -
1 .O0 1.20
- -
1 .O0 1.20
- -
1 .O0 1.20
- -
1.60 2.00
-
-
1.60 2.00
- -
1.60 2.00
-
-
2.50 3
...

  • Relates Information
  • ISO 8130-9:1992

    ISO 8130-9:1992 - Coating powders
    09-28
  • EN 352-2:2020/FprA1

    EN 352-2:2021/oprA1:2023
    09-28
  • IEC TS 61158-4:1999

    IEC TS 61158-4:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 4: Data Link protocol specification Released:3/24/1999 Isbn:2831847656
    09-28
  • HD 566 S1:1990

    HD 566 S1:1998
    09-28
  • ISO 5131:1982/Amd 1:1992

    ISO 5131:1982/Amd 1:1992
    09-28
  • EN 60598-2-22:1990

    EN 60598-2-22:1996
    09-27
  • ISO 8504-2:1992

    ISO 8504-2:1992 - Preparation of steel substrates before application of paints and related products -- Surface preparation methods
    09-27
  • EN 12165:2024

    prEN 12165:2022
    09-27
  • IEC TS 61158-6:1999

    IEC TS 61158-6:1999 - Digital data communications for measurement and control - Fieldbus for use in industrial control systems - Part 6: Application Layer protocol specification Released:3/24/1999 Isbn:2831847613
    09-27
  • ISO 4252:1992

    ISO 4252:1992 - Agricultural tractors -- Operator's workplace, access and exit -- Dimensions
    09-27