|
STANDARD
SIST EN 300 422-1 V2.1.1:2016
ETSI EN 300 422-1 V2.1.1 (2016-09) Wireless Microphones; Audio PMSE up to 3 GHz; Part 1: Class A Receivers; Harmonised Standard covering the essential requirements of article 3.2 of Directive 2014/53/EU
HARMONISED EUROPEAN STANDARD SIST EN 300 422-1 V2.1.1:2016
ETSI ETSI EN 300 422-1 V2.1.1 (2016-09) 2
Reference REN/ERM-TG17-18 Keywords audio, harmonised standard, radio, radio MIC, testing ETSI 650 Route des Lucioles F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00
Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C Association à but non lucratif enregistrée à la Sous-Préfecture de Grasse (06) N° 7803/88
Important notice The present document can be downloaded from: The present document may be made available in electronic versions and/or in print. The content of any electronic and/or print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat. Users of the present document should be aware that the document may be subject to revision or change of status. Information on the current status of this and other ETSI documents is available at If you find errors in the present document, please send your comment to one of the following services: Copyright Notification No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying and microfilm except as authorized by written permission of ETSI. The content of the PDF version shall not be modified without the written authorization of ETSI. The copyright and the foregoing restriction extend to reproduction in all media.
© European Telecommunications Standards Institute 2016. All rights reserved.
DECTTM, PLUGTESTSTM, UMTSTM and the ETSI logo are Trade Marks of ETSI registered for the benefit of its Members. 3GPPTM and LTE™ are Trade Marks of ETSI registered for the benefit of its Members and of the 3GPP Organizational Partners. GSM® and the GSM logo are Trade Marks registered and owned by the GSM Association. SIST EN 300 422-1 V2.1.1:2016
ETSI ETSI EN 300 422-1 V2.1.1 (2016-09) 3 Contents Intellectual Property Rights . 7 Foreword . 7 Modal verbs terminology . 8 Executive summary . 8 Introduction . 8 1 Scope . 10 2 References . 11 2.1 Normative references . 11 2.2 Informative references . 11 3 Definitions, symbols and abbreviations . 13 3.1 Definitions . 13 3.2 Symbols . 15 3.3 Abbreviations . 15 4 Technical requirements specifications . 16 4.1 Radio microphone . 16 4.2 In ear monitoring . 16 4.3 Tour Guide Systems . 17 4.4 Wireless Multichannel Audio Systems. 17 4.5 Environmental profile . 17 5 Testing for compliance with technical requirements . 18 5.1 Presentation of equipment for testing purposes . 18 5.1.1 Introduction. 18 5.1.2 Choice of model for testing . 18 5.1.3 Definitions of alignment and switching ranges . 19 5.1.4 Choice of frequencies . 19 5.1.5 Testing of single channel equipment . 19 5.1.6 Testing of two channel equipment . 19 5.1.7 Testing of multi-channel equipment (more than two channels) . 19 5.1.8 Testing of equipment without a permanent external RF port . 19 5.1.8.1 General . 19 5.1.8.2 Equipment with a permanent internal RF port . 19 5.1.8.3 Equipment with a temporary RF port . 20 5.2 Mechanical and electrical design . 20 5.2.1 General . 20 5.2.2 Physical Controls . 20 5.2.3 Performance testing with integral antenna . 20 5.2.4 Marking (equipment identification) . 20 6 Test conditions, power sources and ambient conditions . 20 6.1 Normal and extreme test conditions . 20 6.2 Test power source . 20 6.3 Normal test conditions . 21 6.3.1 Normal temperature and humidity . 21 6.3.2 Normal test power source voltage . 21 6.3.2.1 Mains voltage . 21 6.3.2.2 Other power sources . 21 6.4 Extreme test conditions . 21 6.4.1 Extreme temperatures . 21 6.4.1.1 General . 21 6.4.1.2 Procedures for tests at extreme temperatures . 21 6.4.2 Extreme test power source voltages . 22 6.4.2.1 Mains voltage . 22 6.4.2.2 Other power sources . 22 SIST EN 300 422-1 V2.1.1:2016
ETSI ETSI EN 300 422-1 V2.1.1 (2016-09) 4 7 General conditions . 22 7.1 Normal test modulation . 22 7.1.1 Analogue systems . 22 7.1.2 Digital systems . 23 7.1.3 WMAS . 24 7.2 Artificial antenna . 24 7.2.1 General . 24 7.3 Test fixture . 24 7.3.1 General . 24 7.4 Test site and general arrangements for radiated measurements. 24 7.4.1 Introduction. 24 7.5 Modes of operation of the transmitter . 25 7.5.1 General . 25 7.6 Arrangement for test signals at the input of the transmitter . 25 7.6.1 General . 25 8 Methods of measurement and limits for transmitter parameters . 25 8.1 Frequency stability . 25 8.1.1 Method of measurement (analogue) . 25 8.1.2 Method of measurement (digital) . 25 8.1.3 Limit . 25 8.2 Rated output power . 26 8.2.1 Method of measurement for equipment without integral antenna . 26 8.2.2 Method of measurement for equipment with integral antenna. 26 8.2.2.1 Method of measurement under normal test conditions . 26 8.2.3 Limit . 26 8.3 Necessary bandwidth . 26 8.3.1 General . 26 8.3.2 Necessary Bandwidth (BN) for Analogue Systems . 27 8.3.2.1 Method of Measurement . 27 8.3.2.2 Limits . 28 8.3.3 Necessary Bandwidth (BN) for Digital Systems . 28 8.3.3.1 Method of Measurement . 28 8.3.3.2 Limits . 30 8.3.4 Necessary Bandwidth (BN) for WMAS . 31 8.3.4.1 Applicability. 31 8.3.4.2 Method of measurement . 31 8.3.4.3 Limits . 32 8.3.5 Bandwidth measurement procedure for PMSE operation in 2,4 GHz to 2,4835 GHz . 33 8.3.5.1 Applicability . 33 8.3.5.2 Definition . 33 8.3.5.3 Limits . 33 8.3.5.4 Conformance . 33 8.3.5.4.1 Test conditions . 33 8.3.5.4.2 Test method . 33 8.3.6 Transmitter Unwanted Emissions in the Out-of-band Domain Alternative Measurement Procedure . 34 8.3.6.1 Applicability . 34 8.3.6.2 Definition . 34 8.3.6.3 Limit . 34 8.3.6.4 Conformance . 35 8.3.6.4.1 Test conditions . 35 8.3.6.4.2 Test method . 35 8.4 Spurious emissions . 37 8.4.1 Definition . 37 8.4.2 Method of measurement . 37 8.4.3 Limits . 37 8.4.4 Measuring receiver . 37 8.5 Transmitter intermodulation distortion . 38 8.5.1 Definition . 38 8.5.2 Method of measurement . 38 8.5.3 Limits . 39 SIST EN 300 422-1 V2.1.1:2016
ETSI ETSI EN 300 422-1 V2.1.1 (2016-09) 5 9 Receiver . 39 9.1 Spurious emissions . 39 9.1.1 Definitions . 39 9.1.2 Method of measuring the power level in a specified load. 40 9.1.3 Method of measuring the effective radiated power of the enclosure . 40 9.1.4 Method of measuring the effective radiated power . 40 9.1.5 Limits . 41 9.2 Receiver sensitivity . 41 9.2.1 Definition . 41 9.2.2 Method of measurement . 41 9.2.3 Limits . 42 9.3 Receiver adjacent channel selectivity . 42 9.3.1 Definition . 42 9.3.2 Method of measurement . 42 9.3.3 Limits . 43 9.4 Receiver blocking . 43 9.4.1 Definition . 43 9.4.2
Method of measurement . 43 9.4.3 Limits . 44 10 Measurement uncertainty . 44 Annex A (normative): Relationship between the present document and the essential requirements of Directive 2014/53/EU . 45 Annex B (normative): Measurement of Necessary Bandwidth (B) for analogue systems . 46 B.1 Test configuration for measurement of the Necessary Bandwidth (B) for analogue systems . 46 Annex C (normative): Radiated measurement . 47 C.1 Test sites and general arrangements for measurements involving the use of radiated fields . 47 C.1.1 General . 47 C.1.2 Anechoic chamber . 47 C.1.3 Anechoic chamber with a conductive ground plane . 48 C.1.4 Open Area Test Site (OATS) . 49 C.1.5 Test antenna . 50 C.1.6 Substitution antenna . 50 C.1.7 Measuring antenna . 51 C.1.8 Stripline arrangement . 51 C.1.8.1 General . 51 C.1.8.2 Description . 51 C.1.8.3 Calibration . 51 C.1.8.4 Mode of use . 51 C.2 Guidance on the use of radiation test sites . 51 C.2.1 General . 51 C.2.2 Verification of the test site . 51 C.2.3 Preparation of the DUT . 52 C.2.4 Power supplies to the DUT. 52 C.2.5 Volume control setting for analogue speech tests . 52 C.2.6 Range length . 52 C.2.7 Site preparation . 53 C.3 Coupling of signals . 53 C.3.1 General . 53 C.3.2 Data signals . 53 C.3.3 Speech and analogue signals . 54 C.3.3.0 General . 54 C.3.3.1 Acoustic coupler description. 54 C.3.3.2 Calibration . 54 C.4 Standard test position . 54 SIST EN 300 422-1 V2.1.1:2016
ETSI ETSI EN 300 422-1 V2.1.1 (2016-09) 6 C.5 Test fixture . 55 C.5.1 General . 55 C.5.2 Description . 55 C.5.3 Calibration .
...