|
TECHNICAL SPECIFICATION
LTE;
Evolved Universal Terrestrial Radio Access (E-UTRA);
Requirements on User Equipments (UEs)
supporting a release-independent frequency band
(3GPP TS 36.307 version 14.6.0 Release 14)
---------------------- Page: 1 ----------------------
3GPP TS 36.307 version 14.6.0 Release 14 1 ETSI TS 136 307 V14.6.0 (2018-07)
Reference
RTS/TSGR-0436307ve60
Keywords
LTE
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the only prevailing document is the
print of the Portable Document Format (PDF) version kept on a specific network drive within ETSI Secretariat.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
If you find errors in the present document, please send your comment to one of the following services:
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2018.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M logo is protected for the benefit of its Members.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3GPP TS 36.307 version 14.6.0 Release 14 2 ETSI TS 136 307 V14.6.0 (2018-07)
Intellectual Property Rights
Essential patents
IPRs essential or potentially essential to normative deliverables may have been declared to ETSI. The information
pertaining to these essential IPRs, if any, is publicly available for ETSI members and non-members, and can be found
in ETSI SR 000 314: "Intellectual Property Rights (IPRs); Essential, or potentially Essential, IPRs notified to ETSI in
respect of ETSI standards", which is available from the ETSI Secretariat. Latest updates are available on the ETSI Web
server (https://ipr.etsi.org/).
Pursuant to the ETSI IPR Policy, no investigation, including IPR searches, has been carried out by ETSI. No guarantee
can be given as to the existence of other IPRs not referenced in ETSI SR 000 314 (or the updates on the ETSI Web
server) which are, or may be, or may become, essential to the present document.
Trademarks
The present document may include trademarks and/or tradenames which are asserted and/or registered by their owners.
ETSI claims no ownership of these except for any which are indicated as being the property of ETSI, and conveys no
right to use or reproduce any trademark and/or tradename. Mention of those trademarks in the present document does
not constitute an endorsement by ETSI of products, services or organizations associated with those trademarks.
Foreword
This Technical Specification (TS) has been produced by ETSI 3rd Generation Partnership Project (3GPP).
The present document may refer to technical specifications or reports using their 3GPP identities, UMTS identities or
GSM identities. These should be interpreted as being references to the corresponding ETSI deliverables.
The cross reference between GSM, UMTS, 3GPP and ETSI identities can be found under
.
Modal verbs terminology
In the present document "shall", "shall not", "should", "should not", "may", "need not", "will", "will not", "can" and
"cannot" are to be interpreted as described in clause 3.2 of the ETSI Drafting Rules (Verbal forms for the expression of
provisions).
"must" and "must not" are NOT allowed in ETSI deliverables except when used in direct citation.
ETSI
---------------------- Page: 3 ----------------------
3GPP TS 36.307 version 14.6.0 Release 14 3 ETSI TS 136 307 V14.6.0 (2018-07)
Contents
Intellectual Property Rights . 2
Foreword . 2
Modal verbs terminology . 2
Foreword . 5
1 Scope . 6
2 References . 6
3 Definitions and abbreviations . 6
3.1 Definitions . 6
3.2 Abbreviations . 7
3.3 Symbols . 7
3A Release independent features . 7
3A.0 General . 7
3A.1 Additional E-UTRA operating bands . 7
3A.2 Additional E-UTRA CA configurations . 8
3A.3 Additional operating bands and/or CA configurations for specific features . 10
3A.4 Other release independent features . 11
4 – 292 Void . 12
Annex A (informative): Frequency arrangement for overlapping operating bands . 13
Annex B (normative): Common Requirements for bands or CA . 14
B.1 Purpose of annex . 14
B.2 Common RRM requirements . 14
B.2.1 Common RRM requirements for a release independent band . 14
B.2.2 Common RRM requirements for an intra-band contiguous CA configuration . 15
B.2.3 Common RRM requirements for an intra-band non-contiguous CA with single uplink configuration . 16
B.2.4 Common RRM requirements for an inter-band CA with single uplink configuration . 17
B.2.5 Common RRM requirements for an inter-band CA with dual uplink configuration . 17
B.2.6 Common RRM requirements for an intra-band non-contiguous CA with dual uplink configuration . 18
B.2.7 Common RRM requirements for an inter-band CA with three uplink configuration . 19
B.2.8 Common RRM requirements for operating bands for UE category NB1. 19
B.2.9 Common RRM requirements for operating bands for UE category 0 . 19
B.2.10 Common RRM requirements for operating bands for UE category M1. 20
B.3 Common UE performance requirements . 20
B.3.1 Void . 20
B.3.2 Common UE performance requirements and tests for different CA configurations and combination
sets . 20
B.3.3 Void . 21
B.3.4 Void . 21
B.3.5 Common UE performance requirements and tests for operating bands for UE category 0 . 21
B.3.6 Common UE performance requirements and tests for operating bands for UE category M1 . 22
B.3.7 Common UE performance requirements and tests for operating bands for UE category NB1 . 22
B.4 Common UE RF requirements . 22
B.4.1 Common UE RF requirements for a release independent band . 22
B.4.2 Common UE RF requirements for an intra-band contiguous CA configuration . 23
B.4.3 Common UE RF requirements for an single uplink inter-band CA configuration . 23
B.4.4 Common UE RF requirements for an inter-band CA configuration including an operating band without
uplink band . 24
B.4.5 Common UE RF requirements for a single uplink intra-band non-contiguous CA configuration . 24
B.4.6 Common UE RF requirements for dual uplink inter-band CA configuration . 25
B.4.7 Common UE RF requirements for dual uplink intra-band non-contiguous CA configuration . 25
ETSI
---------------------- Page: 4 ----------------------
3GPP TS 36.307 version 14.6.0 Release 14 4 ETSI TS 136 307 V14.6.0 (2018-07)
B.4.8 Common UE RF requirements for three uplink inter-band CA configuration . 26
B.4.9 Common UE RF requirements for operating bands for UE category NB1 . 27
B.4.10 Common UE RF requirements for operating bands for UE category 0 . 27
B.4.11 Common UE RF requirements for operating bands for UE category M1 . 27
Annex C (normative): Common Requirements for 4Rx . 29
C.1 Common UE RF requirements . 29
C.2 Common UE demodulation and CSI requirements . 29
Annex D (normative): Common Requirements for performance enhancements for high
speed scenario . 31
D.1 Common RRM requirements for performance enhancements for high speed scenario . 31
D.2 Common UE demodulation requirements for performance enhancements for high speed
scenario . 31
Annex E (normative): Common Requirements for 8Rx . 32
E.1 Common UE RF requirements . 32
Annex F (informative): Change history . 33
History . 37
ETSI
---------------------- Page: 5 ----------------------
3GPP TS 36.307 version 14.6.0 Release 14 5 ETSI TS 136 307 V14.6.0 (2018-07)
Foreword
rd
This Technical Specification has been produced by the 3 Generation Partnership Project (3GPP).
The contents of the present document are subject to continuing work within the TSG and may change following formal
TSG approval. Should the TSG modify the contents of the present document, it will be re-released by the TSG with an
identifying change of release date and an increase in version number as follows:
Version x.y.z
where:
x the first digit:
1 presented to TSG for information;
2 presented to TSG for approval;
3 or greater indicates TSG approved document under change control.
y the second digit is incremented for all changes of substance, i.e. technical enhancements, corrections,
updates, etc.
z the third digit is incremented when editorial only changes have been incorporated in the document.
ETSI
---------------------- Page: 6 ----------------------
3GPP TS 36.307 version 14.6.0 Release 14 6 ETSI TS 136 307 V14.6.0 (2018-07)
1 Scope
The present document specifies requirements for Rel-14 UEs supporting release independent features like:
- additional E-UTRA operating frequency bands on top of Rel-14 of TS 36.101 [2] and TS 36.133 [3];
- additional E-UTRA CA configurations (intra-band/inter-band) on top of Rel-14 of TS 36.101 [2] and TS 36.133
[3];
- additional operating bands and/or CA configurations for specific features (like UE category 0, M1, NB1);
- other release independent features (like 4Rx antenna port, high speed scenario, 8Rx antenna port).
2 References
The following documents contain provisions which, through reference in this text, constitute provisions of the present
document.
• References are either specific (identified by date of publication, edition number, version number, etc.) or
non-specific.
• For a specific reference, subsequent revisions do not apply.
• For a non-specific reference, the latest version applies. In the case of a reference to a 3GPP document (including
a GSM document), a non-specific reference implicitly refers to the latest version of that document in the same
Release as the present document.
[1] 3GPP TR 21.905: "Vocabulary for 3GPP Specifications".
[2] 3GPP TS 36.101: "Evolved Universal Terrestrial Radio Access (E-UTRA); User Equipment (UE)
Radio Transmission and Reception".
NOTE: The considered release is given in the text of the present document that uses [2].
[3] 3GPP TS 36.133: "Evolved Universal Terrestrial Radio Access (E-UTRA); Requirements for
Support of Radio Resource Management".
[4] 3GPP TS 36.306: "Evolved Universal Terrestrial Radio Access (E-UTRA); User Equipment (UE)
radio access capabilities".
NOTE: The considered release is given in the text of the present document that uses [4].
[5] Void
3 Definitions and abbreviations
3.1 Definitions
For the purposes of the present document, the terms and definitions given in 3GPP TR 21.905 [1] and the following
apply. A term defined in the present document takes precedence over the definition of the same term, if any, in 3GPP
TR 21.905 [1].
release independent: applicable to some frozen releases, starting from a certain release Rel-M
NOTE 1: Normally, a feature is introduced only in the latest open release Rel-N and future releases are based on
the previous one so that future releases inherit the requirements of this feature. Introducing a feature "in a
release independent way from Rel-M onwards" (M feature would be also beneficial in previous, already frozen releases starting with Rel-M until Rel-(N-1).
In order to avoid touching TS 36.101 [2] or TS 36.133 [3] of these frozen releases, the corresponding
requirements are captured in TS 36.307 via pointers to [2] or [3] of the release in which the feature was
introduced.
ETSI
---------------------- Page: 7 ----------------------
3GPP TS 36.307 version 14.6.0 Release 14 7 ETSI TS 136 307 V14.6.0 (2018-07)
NOTE 2: Release independent does not mean applicable to all releases.
3.2 Abbreviations
For the purposes of the present document, the abbreviations given in 3GPP TR 21.905 [1] and the following apply. An
abbreviation defined in the present document takes precedence over the definition of the same abbreviation, if any, in
3GPP TR 21.905 [1].
4Rx 4 UE receiver antenna ports
CA Carrier Aggregation
CRS Cell-specific Reference Signal
CSI Channel State Indicator
FDD Frequency Division Duplex
LAA License-Assisted Access
RRC Radio Resource Control
RRM Radio Resource Management
SDR Sustained Data Rate
TDD Time Division Duplex
UE User Equipment
3.3 Symbols
For the purposes of the present document, the following symbols apply:
N Release in which a feature is introduced into TS 36.101 [2] or TS 36.133 [3]
M Release from which onwards (including release M) a feature is release independent
3A Release independent features
3A.0 General
TSG-RAN has agreed for certain features (see the following clauses) to introduce them in a "release independent way".
This means for each feature:
- it is "introduced" in a release N, i.e. TS 36.101 [2] and TS 36.133 [3] of release N define certain UE
requirements for this feature; the feature is indicated in the tables of the following clauses;
- it is "release independent" starting from a release M (M the following clauses;
- UEs supporting this feature have to fulfill additional requirements in release M or higher which are specified in
one or more Annexes of TS 36.307 of release N; the applicable Annexes for a given feature are provided in the
tables of the following clauses.
The applicable UE Categories are specified in TS 36.306 [4] according to the release to which the UE conforms.
3A.1 Additional E-UTRA operating bands
Requirements for a Rel-14 UE for additional E-UTRA operating bands compared to TS 36.101 Rel-14 [2] are
introduced via this clause.
ETSI
---------------------- Page: 8 ----------------------
3GPP TS 36.307 version 14.6.0 Release 14 8 ETSI TS 136 307 V14.6.0 (2018-07)
Table 3A.1-1: E-UTRA operating bands and UE power class
Requirements to be
Release fulfilled
Duplex-
Feature independent (see TS 36.307 of the
mode
from release in which the band
was introduced)
Operating bands, band number <= 64, Power Class 3 FDD, TDD Rel-8 Table B.2.1-1, Table B.4.1-1
Operating bands, band number > 64, Power Class 3 FDD, TDD Rel-9 Table B.2.1-1, Table B.4.1-1
Operating bands, NS-value > 32 FDD, TDD Rel-10 Table B.2.1-1, Table B.4.1-1
Asymmetric operating bands, Power Class 3 FDD Rel-10 Table B.2.1-1, Table B.4.1-1
Operating bands, band number <= 64, Power Class 1 FDD Rel-10 Table B.2.1-1, Table B.4.1-1
Operating bands, Power Class 2 TDD Rel-10 Table B.2.1-1, Table B.4.1-1
For example, Band 19 was introduced in the Release 9 specifications. In order to implement a UE conforming to
Release 8 but supporting Band 19, it is necessary for the UE to additionally conform to some parts of the Release 9
specifications (see corresponding Annexes of TS 36.307 Rel-9 which will point to the requirements in the Rel-9 of TS
36.101 [2] or TS 36.133 [3] to be fulfilled), such as the radio frequency and radio resource management requirements
for the Band 19.
3A.2 Additional E-UTRA CA configurations
Requirements for a Rel-14 UE for additional E-UTRA CA configurations compared to TS 36.101 Rel-14 [2] are
introduced via this clause.
Table 3A.2-1: Intra-band contiguous CA configurations and UE CA power class
requirements to be fulfilled
Release
CA BW Duplex- (see 36.307 of the REL in which
Feature DL/UL independent
Class mode the CA configuration and the
from
power class were introduced)
Table B.2.2-1, Table B.3.2-1,
B FDD Rel-10
Table B.4.2-1
Table B.2.2-1, Table B.3.2-1,
C FDD, TDD Rel-10
Table B.4.2-1
Table B.2.2-1, Table B.3.2-1,
DL D TDD Rel-10
Table B.4.2-1
Intra-band contiguous
Table B.2.2-1, Table B.3.2-1,
E TDD Rel-11
CA configurations,
Table B.4.2-1
power class 3
Table B.2.2-1, Table B.3.2-1,
F TDD Rel-12
Table B.4.2-1
Table B.2.2-1, Table B.3.2-1,
B FDD Rel-10
Table B.4.2-1
UL
Table B.2.2-1, Table B.3.2-1,
C, D FDD, TDD Rel-10
Table B.4.2-1
Intra-band contiguous
Table B.2.2-1, Table B.3.2-1,
CA configurations, UL C TDD Rel-10
Table B.4.2-1
power class 2
NOTE1: The duplex mode "FDD, TDD" refers to a CA configuration composed by only FDD bands or only TDD
bands, respectively.
ETSI
---------------------- Page: 9 ----------------------
3GPP TS 36.307 version 14.6.0 Release 14 9 ETSI TS 136 307 V14.6.0 (2018-07)
Table 3A.2-2: Inter-band CAconfigurations
requirements to be
fulfilled
number Release
number CA BW Duplex- (see 36.307 of the
Feature DL/UL of independent
of CCs Classes mode REL in which the
bands from
CA configuration
was introduced)
Table B.2.4-1, Table
2-4 A, B, C FDD, TDD Rel-10 B.3.2-1, Table B.4.3-
1 or Table B.4.4-1
Table B.2.4-1, Table
2 2-5 D, E FDD, TDD Rel-11 B.3.2-1, Table B.4.3-
1 or Table B.4.4-1
Table B.2.4-1, Table
A, B, C, FDD and
2-5 Rel-12 B.3.2-1, Table B.4.3-
D, E TDD
1 or Table B.4.4-1
Table B.2.4-1, Table
3 A FDD, TDD Rel-10 B.3.2-1, Table B.4.3-
1 or Table B.4.4-1
Table B.2.4-1, Table
3 3-5 B, C, D FDD, TDD Rel-11 B.3.2-1, Table B.4.3-
1 or Table B.4.4-1
DL
Table B.2.4-1, Table
FDD and
3 A
Rel-12 B.3.2-1, Table B.4.3-
TDD
Inter-band CA 1 or Table B.4.4-1
configurations
Table B.2.4-1, Table
4-5 FDD, TDD Rel-11 B.3.2-1, Table B.4.3-
1 or Table B.4.4-1
4 A, C
Table B.2.4-1, Table
FDD and
4-5 Rel-12 B.3.2-1, Table B.4.3-
TDD
1 or Table B.4.4-1
Table B.2.4-1, Table
5 FDD, TDD Rel-12 B.3.2-1, Table B.4.3-
1 or Table B.4.4-1
5 A
Table B.2.4-1, Table
FDD and
5 Rel-12 B.3.2-1, Table B.4.3-
TDD
1 or Table B.4.4-1
Table B.2.4-1, Table
2-4 A, C FDD, TDD Rel-11 B.3.2-1, Table B.4.3-
1 or Table B.4.4-1
UL 2
Table B.2.4-1, Table
FDD and
2-3 A, C Rel-12 B.3.2-1, Table B.4.3-
TDD
1 or Table B.4.4-1
NOTE 1: The duplex mode "FDD, TDD" refers to a CA configuration composed by only FDD bands or only TDD
bands, respectively. The duplex mode "FDD and TDD" refers to a CA configuration including both FDD and
TDD bands.
NOTE 2: CA configurations involving downlink only operation in Band 46 are release independent from Rel-13
onwards (LAA was introduced in Rel-13). The 10 MHz channel bandwidth for Band 46 was introduced in TS
36.101 Rel-14 [2] and can be implemented in a release independent way from Rel-13.
For example, CA configuration CA_1A-19A was introduced in the Release 11 specifications. In order to implement a
UE conforming to Release 10 but supporting the CA configuration CA_1A-19A, it is necessary for the UE to
additionally conform to some parts of the Release 11 specifications (see corresponding Annexes of TS 36.307 Rel-11
which will point to the requirements in the Rel-11 of TS 36.101 [2] or TS 36.133 [3] to be fulfilled), such as the radio
frequency and radio resource management requirements for the CA configuration CA_1A-19A.
ETSI
---------------------- Page: 10 ----------------------
3GPP TS 36.307 version 14.6.0 Release 14 10 ETSI TS 136 307 V14.6.0 (2018-07)
Table 3A.2-3: Intra-band non-contiguous CA configurations
requirements to
be fulfilled
number Release (see 36.307 of
number CA BW Duplex-
Feature DL/UL of sub- independent the REL in which
of CCs Classes mode
blocks from the CA
configuration
was introduced)
Table B.2.3-1,
2 2-5 A, C, D FDD, TDD Rel-11 Table B.3.2-1,
Table B.4.5-1
DL
Intra-band non- Table B.2.3-1,
contiguous CA 3 3-5 A, C FDD, TDD Rel-11 Table B.3.2-1,
configurations Table B.4.5-1
Table B.2.3-1,
UL 2 2 A FDD Rel-11 Table B.3.2-1,
Table B.4.5-1
NOTE 1: The duplex mode "FDD, TDD" refers to a CA configuration composed by only FDD bands or only TDD
bands, respectively.
3A.3 Additional operating bands and/or CA configurations for
specific features
For a specific feature introduced in an earlier release, it may be decided in a later release to apply this specific feature in
a release independent way for additional operating bands and/or CA configurations. For a Rel-14 UE corresponding
requirements are then introduced via this clause.
Table 3A.3-1: Operating bands for specific features
Requirements to be Further information
Release fulfilled
Feature independent (see 36.307 of the REL
from when the feature was
introduced)
Operating bands for Rel-12 Table B.2.9-1, Table B.3.5- Rel-14 WI LC_MTC_LTE_cat0_B25_B26-Core
UE category 0 1, Table B.4.10-1 introduced RF, RRM, demodulation and CSI
requirements for bands 25 and 26, see Table
B.2.9-1, Table B.3.5-1, Table B.4.10-1
Operating bands for Rel-13 Table B.2.10-1, Table Rel-14 WI LTE_MTCe2_L1_cat1_B25_B40-Core
UE category M1 B.3.6-1, Table B.4.11-1 introduced RF, RRM, demodulation and CSI
requirements for bands 25 and 40, see Table
B.2.10-1, Table B.3.6-1, Table B.4.11-1.
Rel-15 WI LTE_bands_R15_M1_NB1-Core
introduced RF, RRM, demodulation and CSI
requirements for bands 14 and 71, see Table
B.2.10-1, Table B.3.6-1, Table B.4.11-1.
Operating bands for Rel-14 Table B.2.11-1, Table Rel-15 WI LTE_bands_R15_M2_NB2-Core
UE category M2 B.4.11-1 introduced RF and RRM requirements for bands
14 and 71, see Table B.2.11-1, Table B.4.11-1.
Operating bands for Rel-13 Table B.2.8-1, Table B.3.7- Rel-14 WI NB_IOT_R14_bands introduced RF,
UE category NB1 1, Table B.4.9-1 RRM and demodulation requirements for bands
11, 21, 25, 31, 70, see Table B.2.8-1, Table B.3.7-
1, Table B.4.9-1.
Rel-15 WI LTE_bands_R15_M1_NB1-Core
introduced RF and RRM for bands 4, 14 and 71
see Table B.2.8-1, Table B.4.9-1.
Operating bands for Rel-14 Table B.2.12-1, Table 3.7- Rel-15 WI LTE_bands_R15_M2_NB2-Core
UE category NB2 1, Table B.4.9-1 introduced RF, RRM and demodulation
requirements for bands 4, 14 and 71, see Table
B.2.12-1, Table 3.7-1, Table B.4.9-1.
ETSI
---------------------- Page: 11 ----------------------
3GPP TS 36.307 version 14.6.0 Release 14 11 ETSI TS 136 307 V14.6.0 (2018-07)
Table 3A.3-2: CA configurations for specific features
Requirements to be Further information
Release fulfilled
Feature independent (see 36.307 of the REL
from when the feature was
introduced)
Operating bands for Rel-14 Table B.2.13-1, Table Rel-15 WI V2X new band combinations (V2X_5A-
V2X communication B.4.12-1 47A, V2X_20A-47A, V2X_34A-47A, V2X_28A-
with con-current 47A, V2X_71A-47A) introduced and should be
operation satisfied for the RF and RRM requirements in
Table B.2.13-1, Table B.4.12-1
Operating band for Rel-14 Table B.2.13-1, Table In Rel-15 WI for eV2X, introduce intra-band multi-
V2X communication B.4.12-1 carrier V2X_47C and V2X_47C1 and should be
with multi-carrier at satisfied for the RF and RRM requirements in
Band 47 Table B.2.13-1, Table B.4.12-1
3A.4 Other release independent features
This clause covers requirements for a Rel-14 UE coming from all other release independent features that are not
covered under clause 3A.1, 3A.2 and 3A.3, e.g. generic baseband requirements or requirements that are not band/CA
configuration specific.
ETSI
---------------------- Page: 12 ----------------------
3GPP TS 36.307 version 14.6.0 Release 14 12 ETSI TS 136 307 V14.6.0 (2018-07)
Table 3A.4-1: Additional requirements of other release independent features
Requirements to be Further information
Release fulfilled
Feature independent (see 36.307 of the REL
from when the feature was
introduced)
RF and Rel-10 Table C.1-1, Table C.2-1 REL-13 WI LTE_4Rx_AP_DL introduced:
performance for single carrier and Table - single carrier RF requirements for bands 1, 2, 3,
requirements for C.1-2, Table C.2-2 for CA 7, 20, 39, 41, 42: see Table C.1-1
4Rx UEs - CA RF requirements for CA_3A-42A and other
1UL CA configurations (see TS 36.101 REL-13 [2]
Table 7.3.1A-0a NOTE 20): see Table C.1-2
- single carrier performance requirements for
demodulation and CSI: see Table C.2-1
REL-14 WI LTE_4Rx_AP_DL_bands introduced:
- single carrier RF requirements for band 35, 40:
see Table C.1-1
- CA RF requirements for
...