|
TECHNICAL SPECIFICATION
Digital Enhanced Cordless Telecommunications (DECT);
Ultra Low Energy (ULE);
Machine to Machine Communications;
Part 2: Home Automation Network (phase 2)
---------------------- Page: 1 ----------------------
2 ETSI TS 102 939-2 V1.3.1 (2019-01)
Reference
RTS/DECT-ULE274
Keywords
access, data, DECT, environment, IMT-2000,
intelligent homes & buildings, internet,
interoperability, interworking, M2M, mobility,
packet mode, profile, radio, synchronization,
TDD, TDMA
ETSI
650 Route des Lucioles
F-06921 Sophia Antipolis Cedex - FRANCE
Tel.: +33 4 92 94 42 00 Fax: +33 4 93 65 47 16
Siret N° 348 623 562 00017 - NAF 742 C
Association à but non lucratif enregistrée à la
Sous-Préfecture de Grasse (06) N° 7803/88
Important notice
The present document can be downloaded from:
The present document may be made available in electronic versions and/or in print. The content of any electronic and/or
print versions of the present document shall not be modified without the prior written authorization of ETSI. In case of any
existing or perceived difference in contents between such versions and/or in print, the prevailing version of an ETSI
deliverable is the one made publicly available in PDF format at www.etsi.org/deliver.
Users of the present document should be aware that the document may be subject to revision or change of status.
Information on the current status of this and other ETSI documents is available at
If you find errors in the present document, please send your comment to one of the following services:
Copyright Notification
No part may be reproduced or utilized in any form or by any means, electronic or mechanical, including photocopying
and microfilm except as authorized by written permission of ETSI.
The content of the PDF version shall not be modified without the written authorization of ETSI.
The copyright and the foregoing restriction extend to reproduction in all media.
© ETSI 2019.
All rights reserved.
TM TM TM
DECT , PLUGTESTS , UMTS and the ETSI logo are trademarks of ETSI registered for the benefit of its Members.
TM TM
3GPP and LTE are trademarks of ETSI registered for the benefit of its Members and
of the 3GPP Organizational Partners.
oneM2M™ logo is a trademark of ETSI registered for the benefit of its Members and
of the oneM2M Partners.
GSM and the GSM logo are trademarks registered and owned by the GSM Association.
ETSI
---------------------- Page: 2 ----------------------
3 ETSI TS 102 939-2 V1.3.1 (2019-01)
Contents
Intellectual Property Rights . 9
Foreword . 9
Modal verbs terminology . 9
Introduction . 10
1 Scope . 11
2 References . 11
2.1 Normative references . 11
2.2 Informative references . 12
3 Definition of terms, symbols and abbreviations . 13
3.1 Terms . 13
3.2 Symbols . 13
3.3 Abbreviations . 14
4 Description of services and features . 16
4.1 DECT Ultra Low Energy . 16
4.1.0 General . 16
4.1.1 Back-compatibility with ULE Phase 1. 17
4.1.2 Coexistence with other DECT services . 17
4.1.3 Example applications covered by ULE Phase 2 . 17
4.1.3.0 General . 17
4.1.3.1 Simple medical pendant alarms . 17
4.1.3.2 Software Upgrade Over The Air . 18
4.1.3.3 M2M devices with audio capability . 18
4.2 Requirements for ULE Phase 2 . 19
4.2.1 Device types. 19
4.2.1.0 General . 19
4.2.1.1 ULE Phase 2 RFP . 19
4.2.1.1.1 General description . 19
4.2.1.1.2 Requirements . 19
4.2.1.2 PP type IV: hybrid device with voice/data support . 19
4.2.1.2.1 General description . 19
4.2.1.2.2 Requirements . 19
4.2.2 U-plane interworking and protocol architecture . 19
4.2.3 Performance Objectives . 20
4.3 Services and features implemented by ULE phase 2 . 20
4.3.0 General . 20
4.3.1 MAC/PHY layer . 20
4.3.2 DLC layer . 20
4.3.3 NWK layer . 20
4.3.4 Interworking and Application layer . 21
4.3.5 Security . 21
4.3.6 Management Entity . 21
4.3.7 Speech services and codecs . 21
5 Service and feature definitions . 21
5.1 ULE Phase 2 . 21
5.1.1 PHL service definitions . 21
5.1.2 MAC service definitions . 21
5.1.3 DLC service definitions . 22
5.1.4 NWK feature definitions . 22
5.1.5 Application feature definitions . 23
5.1.6 Management Entity (ME) definitions . 23
5.1.7 U-plane service and interworking definitions . 23
5.1.8 ULE device types . 23
5.1.9 Speech services and speech coding definitions . 23
ETSI
---------------------- Page: 3 ----------------------
4 ETSI TS 102 939-2 V1.3.1 (2019-01)
5.1.10 Call Control (CC) and mobility management service definitions . 24
6 Profile specific requirements . 24
6.1 General . 24
6.2 Specific conventions. 24
6.2.1 Use of symbols in support status tables . 24
6.3 DECT ULE phase 1 device types . 24
6.3.1 Types of devices supported by the present document . 24
6.3.2 Specific procedures for specific device types . 25
6.4 Physical layer (PHL) requirements. 25
6.4.1 Physical layer (PHL) services . 25
6.4.2 Modulation schemes . 25
6.4.3 PHL service to procedure mapping . 26
6.5 MAC layer requirements . 26
6.5.1 MAC layer services . 26
6.5.2 MAC service to procedure mapping . 27
6.6 DLC layer . 29
6.6.1 DLC layer services. 29
6.6.2 DLC service to procedure mapping . 30
6.7 NWK layer . 31
6.7.1 General . 31
6.7.2 NWK features . 31
6.7.3 NWK features to procedures mapping . 33
6.8 Application Layer . 34
6.8.1 Application features . 34
6.8.2 Application features to procedures mapping. 35
6.9 Distributed communications . 35
6.10 Management Entity (ME) . 35
6.10.1 Management Entity (ME) services . 35
6.10.2 Management Entity (ME) mode to procedures mapping . 36
6.11 U-plane services and interworking requirements . 37
6.11.1 U-plane and interworking services . 37
6.11.2 U-plane and interworking service to procedure mapping . 37
6.12 Speech Services . 38
6.12.1 Speech Services features . 38
6.12.2 Speech Services to procedures mapping . 38
6.13 General class/service/interworking support . 39
6.13.1 Class/service support . 39
6.13.2 Protocol interworking support . 39
7 Profile specific procedures description . 40
7.0 General . 40
7.1 Back compatibility with ULE Phase 1 . 40
7.1.0 General . 40
7.1.1 Back compatibility with a ULE Phase 1 Fixed Part (FP) . 40
7.1.2 Back compatibility with a ULE Phase 1 Portable Part (PP) . 40
8 Physical Layer (PHL) procedures . 40
9 Management Entity (ME) procedures . 40
9.1 ULE phase 1 Management . 40
9.2 Channel selection and collision avoidance procedures. 40
9.3 Channel selection and collision avoidance procedures for US region . 41
9.3.0 General . 41
9.3.1 Overall architecture of ULE channel selection processes . 41
9.3.2 Process M0 (RFP side pre-selection process) . 41
9.3.3 Broadcast mechanism . 41
9.3.4 Process M1 (PP side channel selection process) . 42
9.3.5 Setup attempt and evaluation of responses . 42
9.3.6 Process M2 (collision handling/collision avoidance process) . 43
9.4 Channel selection and collision avoidance procedures for Japan region . 43
9.4.0 General . 43
9.4.1 Overall architecture of ULE channel selection processes . 43
ETSI
---------------------- Page: 4 ----------------------
5 ETSI TS 102 939-2 V1.3.1 (2019-01)
9.4.2 Process M0 (RFP side pre-selection process) . 43
9.4.3 Broadcast mechanism . 44
9.4.4 Process M1 (PP side channel selection process) . 44
9.4.5 Setup attempt and evaluation of responses . 44
9.4.6 Process M2 (collision handling/collision avoidance process) . 45
10 MAC layer procedures . 45
10.1 Radio Control Bits . 45
10.1.1 Quiet Channel Indication . 45
10.1.2 PHS Detection Indication . 45
10.2 Downlink broadcast (A-field). 46
10.2.0 General . 46
10.2.1 N messages . 46
T
10.2.2 Q messages . 46
T
10.2.2.1 Q - static system information . 46
T
10.2.2.2 Q - FP capabilities . 46
T
10.2.2.2.1 Standard FP Capabilities . 46
10.2.2.2.2 Extended FP Capabilities. 47
10.2.2.2.3 Extended FP Capabilities part 2 . 47
10.3 Slot types and slot use . 48
10.3.1 Full Slot . 48
10.3.1.1 General . 48
10.3.1.2 Use of full slot in C/O bearers . 48
10.3.1.3 Use of full slot in C/L dummy bearers . 48
10.3.2 Short Slot . 48
10.3.2.1 General . 48
10.3.2.2 Use of short slot in C/O bearers . 48
10.3.3 Long Slot . 49
10.3.3.1 General . 49
10.3.3.2 Use of long slot in C/O bearers . 49
10.4 No-emission legacy mode procedures . 49
10.4.1 General . 49
10.5 U-plane C/L downlink services . 49
10.5.0 General . 49
10.5.1 U-plane C/L downlink multicast unacknowledged service . 50
10.5.1.0 General . 50
10.5.1.1 Logical channels and instance separation . 50
10.5.1.2 Addressing and management of multicast groups . 50
10.5.1.3 Procedure . 50
10.5.1.4 SI subfield format . 50
P
10.5.2 U-plane C/L downlink over the dummy bearer . 50
10.5.2.0 General . 50
10.5.2.1 Multiplexing cycle . 51
10.5.2.2 Single-burst transmission . 51
10.5.2.3 Identification of C/L downlink insertion . 51
10.5.2.4 Announcement via the B paging channel and identification of instances . 51
U
10.5.3 U-plane C/L downlink over additional C/L bearers . 51
10.5.3.0 General . 51
10.5.3.1 Channel selection and transmission start. 52
10.5.3.2 MAC signalling in the additional C/L downlink bearer . 52
10.5.3.3 Single-burst transmission . 52
10.5.3.4 Announcement via the B paging channel and identification of instances . 52
U
10.5.4 Repetition of U-plane C/L downlink . 53
10.6 ULE Paging Procedures (phase 2) . 53
10.6.0 General . 53
10.6.1 P Paging Message Formats . 54
U
10.6.2 Paging Descriptors for ULE Paging . 54
10.6.2.1 Basic concepts of the ULE paging system . 54
10.6.2.2 Basic operation of the descriptors . 54
10.6.2.3 Allocation of descriptors . 54
ETSI
---------------------- Page: 5 ----------------------
6 ETSI TS 102 939-2 V1.3.1 (2019-01)
10.6.2.4 Format for descriptors in ULE phase 1 .
...